All Installation Instructions for General Electric Range 19571-1

remove and replace

very easy remove the bad bulb install the new one

Parts Used:

Fluorescent Lamp/Bulb

Perry from Flushing, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 24 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced more for cosmetic reasons

Your support team helped tremendously in ordering the parts. Parts arrived in only 2 days. Upon taking the door off the oven we had to remove several screws, then more screws. Was able to take it almost fully apart, replace old broken parts with new. Putting it back together was like a puzzle. We did it though and saved money! Thanks

Parts Used:

Bottom Trim - White

TRIM VENT & CLIP White

Glenda from Port Richey, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bottom trim had rusted, so we needed new piece

Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)

Parts Used:

Bottom Trim - White

Robin from Apple Valley, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The trim piece on the bottom of the door was rusted making the unit look really dirty and used.

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

Parts Used:

Bottom Trim - White

Glenn from West Melbourne, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Part rusted over time...22 years.

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

Parts Used:

Bottom Trim - White

Jeannene from HUNTINGTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

rusted trim strip

remove screws, re-install screws

Parts Used:

Bottom Trim - White

Larry from Sarasota, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No Spin Cycle

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

Parts Used:

Screws - Package of 12

Richard from LORDSBURG, NM
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

Parts Used:

Bottom Trim - White

Donald from FAYETTEVILLE, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bottom trim had rusted out from water build-up

disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.

Parts Used:

Bottom Trim - White

john from buford, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Fluorescent lamp bulb

Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.

Parts Used:

Fluorescent Lamp/Bulb

Danial from HILLSBORO, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip pans were filthy after years of overflow from pots during cooking

Luckily I retained the original manual and was able to order the drip pans through your company from the original manufacturer. Be sure range is turned off, lift the burner locking element, then lift the burner a bit. Remove the burner by pulling it, disconnecting it through the opening in the drip pan. Lift out the old drip pan and replace it with the new one. Then reconnect the burner through the opening in the drip pan. Press the burner locking element in place and the job is done

Parts Used: