My Orders
195431-2 Briggs and Stratton Engine - Overview
Models starting with 195431-2
Click on the best match to narrow your results.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$14.95
Special Order
Brace-air Cleaner
Part #224484
$25.95
Special Order
Bushing-valve Guide
Part #231218
This genuine item is supplied by the original equipment manufacturer for use with engines, generators, lawn mowers, lawn tractors, and snowblowers made by Briggs & Stratton, Toro, Lawn Boy, and Murray. The valve guide bushing is made out of metal. It may require a screwdriver and a wrench during installation. This part will need to be replaced if it breaks. This item is sold individually.
$64.95
Special Order
Gasket Set-engine
Part #299577
It is a genuine replacement part that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. Gaskets are generally utilized to provide a tight seal between connected parts. It is an identical replacement for a missing or a faulty hardware that...Read more was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and use of these parts. Keep in mind this high-quality set is sold individually.
Read less
$61.95
Special Order
Bearing-ball
Part #691069
$18.95
Special Order
Kit-needle/seat
Part #394682
This is an authentic manufacturer-supplied kit which is specially made for use with Briggs and Stratton engines that are commonly installed on a variety of lawn and garden equipment. This kit included the float needle and the needle seat. The needle and seat work like a valve to allow fuel into the carburetor bowl when the bowl drains and...Read more stops fuel intake when the bowl is full. To ensure the correct repair procedure, refer to the appropriate diagrams for your model.
Read less
$23.95
Special Order
Kit-needle/seat
Part #394683
This is an authentic Briggs & Stratton replacement part. The needle valve is designed by the manufacturer for use in engines. This part includes the needle, a spring retainer, and a bearing, and it is placed in the carburetor assembly to control the flow of fuel. You may require a screwdriver when replacing this part. This item is sold individually.
$54.95
Special Order
Nozzle-Carburetor
Part #398202
$64.95
Special Order
Cup-Flywheel
Part #691173
$70.95
Special Order
Clutch-starter
Part #399671
Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.
Read less
$7.95
Special Order
Screw
Part #690323
$6.95
Special Order
Screw
Part #690278
$93.95
Special Order
Engine Ring Gear
Part #696537
Common Symptoms of models starting with 195431-2
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
3 of 10 people
found this instruction helpful.
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill sw ... Read more itch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill sw ... Read more itch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!