1940 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
difficulty unplugging the power pigtail
2 of 3 people
found this instruction helpful.
-
William from Las Cruces, NM
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Just kept working on it.
Was this helpful?
Thank you for voting!
Quit making ice
2 of 3 people
found this instruction helpful.
-
James from Charleston, SC
- Easy
- 15 - 30 mins
-
Screw drivers
Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient
... Read more
like I was and think the new unit was bad or that you replaced the wrong part)
Read less
Was this helpful?
Thank you for voting!
noisy fridge, perimeter of door heating up
2 of 3 people
found this instruction helpful.
-
craig from maple grove, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.
Was this helpful?
Thank you for voting!
Old Valve was dead
2 of 3 people
found this instruction helpful.
-
Joseph from Bloomfield Hills, MI
- Really Easy
- 15 - 30 mins
-
Pliers
This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!
Was this helpful?
Thank you for voting!
ice maker quit working
2 of 3 people
found this instruction helpful.
-
Randy from Yale, OK
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.
Was this helpful?
Thank you for voting!
refrigerator was overheating, condensor fan dead.
2 of 3 people
found this instruction helpful.
-
David from Granada Hills, CA
- Really Easy
- 15 - 30 mins
First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!
Read less
Was this helpful?
Thank you for voting!
Ice from icemaker taste metallic; new ice maker directly from box
2 of 3 people
found this instruction helpful.
-
Samuel from ALEXANDRIA, VA
- Difficult
- More than 2 hours
I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.
Was this helpful?
Thank you for voting!
My ice maker wouldn't make ice. The heaters shorted out and fried the wiring and little motor.
1 person
found this instruction helpful.
-
James R. from Laguna Beach, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Saw many photos on the Internet that looked like my ice maker, but they were different. I put in my Refrigerator model No. and found my exact replacement ice maker right away. I was a little cautious, because the new one didn't include the wiring harness, or the plastic cover. I took the chance and ordered it. Super fast delivery, a Day o
... Read more
r 2 at most. Everything went smoothly, and after the new one was in, I crossed my fingers until the timer kicked in, and I started hearing ice cubes falling in the tray about 3 hours later. Success! I had been having problems with the ice maker almost from the beginning. Hopefully, the replacement will last longer. I will say that this Maytag Fridge. is the absolute worst kitchen appliance I've ever owned in my 47 years of house keeping! The defroster went in the freezer a couple of months after the Warranty ended, and it cost me $375.00 to have a Tech, come in to repair. I got away easy this time, buying the ice maker for $135.00 and being able to do the work myself.
Jim
Jim
Read less
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people
found this instruction helpful.
-
Richard from North Easton, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi
... Read more
er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Read less
Was this helpful?
Thank you for voting!
Ice Maker Stopped Working
1 person
found this instruction helpful.
-
Mark from Oak Hill, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
This was a very easy fix. I took the old ice maker out, including the electrical harness. Switched the harness and stop bar to the new ice maker on my bench, then installed the new assembly. Ice initially had some hollow cubes. I checked the ice maker for level. But it was fine. Thought it might be moving too fast. But it seems to
... Read more
have cleared up. Perhaps it took some time to completely cool down.
Read less
Was this helpful?
Thank you for voting!
Original ice maker was leaking
1 person
found this instruction helpful.
-
KEN from FOUNTAIN HILLS, AZ
- Easy
- 15 - 30 mins
-
Screw drivers
There are 3 screws holding the icemaker in place. After removing the ice bucket, I removed the screws, then twisted the unit to gain access to the power plug. The plug is held in place by a plastic flap which is part of the connector. It has to be pushed down to remove the connector. The new unit went in perfectly and performed flawlessly
... Read more
for 3 days until the compressor blew out! After feeling some sense of accomplishment having fixed the icemaker, I learned that my neglecting to clean the vent grill in the front of the refrigerator had caused its demise. Don't forget to clean the dust out of the vents!
Read less
Was this helpful?
Thank you for voting!
Ice Maker Died
1 person
found this instruction helpful.
-
Robert from West Ossipee, NH
- Easy
- 15 - 30 mins
-
Nutdriver
When that one came and I went to install it, I found that my fridge was so old (almost 30 years) that the wire harness on the old icemaker could not be transferred to the new one. The old one was hand wired into the guts of the machine with wire nuts and other connectors. The new unit needs a plug in harness to match a plug connection on
... Read more
the ice maker. Also, the bent wire arm that senses ice bin levels was different, old unit hooked in with clips and such, new one pops into a socket in the new ice maker.
I called PartSelect back again, and the clerk spent a lot of time in the books (no parts in the online listings) and found new style connector and wire arm. Another 25 dollars and problem is solved.
Once those parts came, the actual installation was a breeze. Remove three screws, unplug the ice maker from the back wall of the fridge, plug new wire harness into new ice maker and the back wall of the frige, install new ice maker with the same three screws, pop the new style bent wire arm into place and pop the plastic cover from the old ice maker onto the front of the new one. Done! Took me ten minutes (plus two weeks of chasing parts, but only half an hour of actual time in those two weeks).
I let it make a couple of loads of ice that I disposed of (to capture any dust and crud that might have been on or in the new ice maker) and then turned it loose. We had a nice full bin of ice in the morning.
I called PartSelect back again, and the clerk spent a lot of time in the books (no parts in the online listings) and found new style connector and wire arm. Another 25 dollars and problem is solved.
Once those parts came, the actual installation was a breeze. Remove three screws, unplug the ice maker from the back wall of the fridge, plug new wire harness into new ice maker and the back wall of the frige, install new ice maker with the same three screws, pop the new style bent wire arm into place and pop the plastic cover from the old ice maker onto the front of the new one. Done! Took me ten minutes (plus two weeks of chasing parts, but only half an hour of actual time in those two weeks).
I let it make a couple of loads of ice that I disposed of (to capture any dust and crud that might have been on or in the new ice maker) and then turned it loose. We had a nice full bin of ice in the morning.
Read less
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people
found this instruction helpful.
-
Douglas from Mesa, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
install new icemaker
2 of 4 people
found this instruction helpful.
-
Nancy from Englewood, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
First had to remove baskets and door from freezer. Removed three screws; removed old ice maker; Attached new ice maker with three screws; removed arm from old ice maker and placed in the new ice maker. Replaced door and baskets
Was this helpful?
Thank you for voting!
Kickplate clip broke off
2 of 4 people
found this instruction helpful.
-
Paul from Fort Wayne, IN
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Reattaching the kickplate clip was easy, but the tab that holds in place was broken. It would slide back when the kickplate was installed. I fashioned a replacement tab out of a piece of 3/32 aluminum bent into a U with the hammer. To hold it in place I drilled and tapped one hole and used a 6-32 machine screw.
Was this helpful?
Thank you for voting!