19145 - Instructions

All Instructions for the 19145
121 - 135 of 544

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker Leaked Creating an Ice block
2 of 3 people found this instruction helpful.
  • Loren from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this helpful?
Thank you for voting!
Replaced leaking ice maker after minor screwup!
2 of 3 people found this instruction helpful.
  • Jackson from Leesburg, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver
Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cab le wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people found this instruction helpful.
  • Gail from Golden, CO
  • Really Easy
  • Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
icemaker quit working
2 of 3 people found this instruction helpful.
  • craig from green bay, WI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.
Was this helpful?
Thank you for voting!
Replaced Ice Maker
2 of 3 people found this instruction helpful.
  • Steven from Clinton Corners, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people found this instruction helpful.
  • Paul from Lowell, MI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
ice maker kept on dripping water causing ice in the icee containergood compression to freeze in a block
1 person found this instruction helpful.
  • Fernand from SOMERSET, MA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed re adily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.
Was this helpful?
Thank you for voting!
Ice maker broken. Quick fix
1 person found this instruction helpful.
  • Tim from Berkeley, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
Was this helpful?
Thank you for voting!
icicles from pooled water in ice collector bucket
1 person found this instruction helpful.
  • Roberta A from WINTER HAVEN, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cube s (without the extra icicles) in 1 hour...
Was this helpful?
Thank you for voting!
My amana side to side freezer stoped freezing i found parts select and helped my get a part that by % would be the problemand it worked thanks
1 person found this instruction helpful.
  • Martin from SAN ANTONIO, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I replaced the run capacitor wich is located near the compressor, i first turned power off to fridge than remuved capacitor checked for continuity and the capacitor was the problem thanks
Was this helpful?
Thank you for voting!
Ice Maker leaking.
1 person found this instruction helpful.
  • Jeannine from Pontiac, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I watched the video regarding the instillation of this ice maker a few times and then followed it exactly. It was incredibly easy. We had ice cubes about two hours later and no longer had a leak making icebergs!
Was this helpful?
Thank you for voting!
Location of the run capacitor was not as the video described.
1 person found this instruction helpful.
  • Robert from Webbers Falls, OK
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigera tor is still too wide but it's colder.
Was this helpful?
Thank you for voting!
Ice Maker Cycling But Not Making Ice
1 person found this instruction helpful.
  • Todd from STATE COLLEGE, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Adding water to Ice Maker, caused ice to be made. I assumed the Single Outlet Water Valve to be problem (despite %4 probability). I suppose problem could have been in the ice maker itself and it's interface to the Single Outlet Water Valve but fortunately the Single Outlet Water Valve solved the problem. The Parts Select replacement par t video was very helpful and the replacement was fairly easy. Were the problem in the Ice Maker itself, I don't know that I could have justified the cost of the the repair for a 17 year old refrigerator.
Was this helpful?
Thank you for voting!
Replace Ice Maker
1 person found this instruction helpful.
  • Dan from LAVISTA, NE
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridic ulously hard to get out. Never did do it, just worked around it. Working perfect now.
Was this helpful?
Thank you for voting!
Ice tray was corroded and leaking
1 person found this instruction helpful.
  • Scott from SAN DIEGO, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver
Removed top drawer from freezer. Unplugged the ice maker. Uncrewed the bottom screw. Loosened the two top screws. Removed old ice maker. Removed all the parts that didn't come with the new ice maker and installed on new ice maker. Reinstalled the new ice maker. Started making ice with no leaks in about 3 hours.
Was this helpful?
Thank you for voting!
All Instructions for the 19145
121 - 135 of 544