1902 - Instructions

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

Replaced handle. Very Easy.

The repair was simple and expensive for a little piece of plastic that was the wrong color and only color available. We have a white trash compactor and had to order a black one. The hardest and most time consuming part of the repair was painting the handle. In order to paint a Black Plastic handle white we had to use special primer an ... Read more d special paint. Before using the primer, we had to wash the plastic handle with paint thinner, then rinse and let dry completely. Other than the cost and the aggravation, it was fine. And it was less than buying a new one. : )

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which ... Read more the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.

refloored the floor and so the unit would not come out. had to cut tile, broke edge off of formica counter but once the unit was out a piece of cake. 6 self tapping screws removed , right on the top, two screws holding the cover for the power nuts, replaced broken nut, leveled ram, replaced nuts and ready to slide back in. After thought, ... Read more I had one nut on hand from a few years earlier. I ordered two new nuts and now i am going to pull the unit again and replace both nuts. thought being a longer period before having to do this again. The unit was put in in 1981 and used continuously.

Very simple, changed the gear, adjusted the drive and tested. Very straight forward.

replaced the large gear and put it back together.

Took out old gears replaced with new very easy with your dirictions.

Used visuals from partselect web site to dismantle the trash compactor , remove broken power nut , order new nuts. Only took a few days to receive new nuts. Replaced nuts , put back together and now works fine.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

Ordered three parts, however if I had read your repair page more thoroughly I could have avoided buying the top of cycle off switch. Oh well... This thirty year old trash compactor is back in business running like a new one. My one recommendation? READ YOUR FAQ PAGE. It will save you money.dan

Ordered part and received it in two days. Unplugged the compactor from wall outlet. Removed two screws holding control panel in place, marked proper wire location on rear of panel, disconnected push-on terminations from start/run switch. Removed knurled nut holding start/run switch onto the control panel and substituted the new switch. ... Read more Reassenbled everything in reverse order to disassembly and plugged power cord back into the wall outlet. No further work required.

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!

Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed f ... Read more rom the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.