1902 - Instructions

Someone pulled a Conan on the compactor handle and broke it loose--no one admitted doing it but I have my suspicions. Since the compactor was installed during the first Bush administration, I assumed that the part would be unavailable. I tried to glue it with the latest "super" bond epoxy/space shuttle goop and it would not hold. A frien ... Read more d tried to plastic weld the crack--it worked until Conan showed up again and ripped it loose. I was ready to look for a new compactopr but since it had an insert that matched the custom cabinets--that I knew would not fit on a new unit--I looked on the internet for a part.
The part number was entered, the part was in stock and the order placed on Sunday afternoon. The part arrived on Tuesday and was installed in less than two minutes. It was the high point of the week.

pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.

As per directions

Put the parts in and reinstalled it back in it place

Move the unit out of the cabinet, and take off the top cover.The two drive screws are easy to see. unscrew the two screws of one of the power nut covers and remove that cover. With pliers, unscrew the plastic power nut from that screw. Screw on the replacement power nut with the help of pliers and some heavy grease. install the bearin ... Read more g cap. Use the same procedure for replacing the plastic power nut on the other screw. To make sure the piston is level, place the cover on the power screw but do not attach it. Measure from the end of the screw to the top of the cover of the first screw, then adjust the second power nut up or down so the two power screw nut covers are the same distance down from the top of the it's power screw Lift up the piton assembly to close the gap, if any (I used a short piece of rope) , and install the screws on the second power bearing cap. After installation. recheck the distance from the top of the power screws to the power bearing caps is close to the same distance so the piston will be level.. This same procedure could be followed for other brands. Power of the appliance and verify functionality, if OK replace the top cover and push unit back into the cabinet..

REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES

Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.

Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.

Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.

Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.

There were two screws holding the handle on, We removed the two screws, removed the broken handle and screwed the new handle on.

Removed and replaced in less than 15 minutes. Works like new again

Took under 5 minutes to unscrew old handle and screw on the new one. Identical part to old handle, compactor looks and works like new!

Unscrewed old one. Slide new one in. Screwed in two screws. Done. The handle ended up being black, even though the part was listed as brown.... that is good, because the original part was black.
So glad you had the part. It was pricey, but way less than a new trash compactor!