18985 ((1988)) Kenmore Dishwasher - Instructions

Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days later i had the parts, and the next day I had a fully functioning leak free dishwasher.

The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

Replaced with a new rinse aid fill cap.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

First I opened the package and screwed the new dispenser cap into place.

Unscrewed old one and installed the new one.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

Simply screwed in new cap

Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

Put on a new cap.

I Just Open Door And Put Fill Cap In And Turn That It