1765 - Instructions

All Instructions for the 1765
31 - 45 of 60

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
holder burnt
0 of 1 people found this instruction helpful.
  • Paul from lewiston, ME
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Was this helpful?
Thank you for voting!
contacts had gotten burnt out/blackened with age so burner was intermittent.
0 of 1 people found this instruction helpful.
  • john from reading, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this helpful?
Thank you for voting!
Wire broken off plug in block
0 of 1 people found this instruction helpful.
  • Robert from Phillipsburg, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
Was this helpful?
Thank you for voting!
The knob had worn out and I needed it replaced.
0 of 1 people found this instruction helpful.
  • Rev. O. C. from North Little Rock, AR
  • Really Easy
  • Less than 15 mins
All I had to was fit the knob on the stem of the burner and push on it and turn the knob.
Was this helpful?
Thank you for voting!
Burner Would Not Heat
0 of 1 people found this instruction helpful.
  • David from Toledo, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this helpful?
Thank you for voting!
Wire broken going to one electric plug for burner
0 of 1 people found this instruction helpful.
  • John from Shelby Township, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.
Was this helpful?
Thank you for voting!
no heat from burner
0 of 1 people found this instruction helpful.
  • George from ST. Charles, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this helpful?
Thank you for voting!
just put it on
0 of 1 people found this instruction helpful.
  • Cathy from Landrum, SC
  • Really Easy
  • Less than 15 mins
Needed new knobs to go on the stove. I only had one left in the original ones for the stove that was bought 27 years ago.
Was this helpful?
Thank you for voting!
needed replacement knobs
0 of 1 people found this instruction helpful.
  • Marcia from Sandston, VA
  • Really Easy
  • Less than 15 mins
My stove is well over 15 years. When I bought my house over 7 years ago the stove was ancient and had only 2 knobs. Well, one of the two fell apart and I could not afford to replace the stove. Lo and behold there was a part number on the back of the knob and I did a goggle search and found an identical replacement. The kind they sell at the store, the adjustable ones, did not work. Anyway, I placed the order during the New Year holiday and I got my knobs in 2 days. Beautiful and shiny and best of all I can use all my burners for the first time ever.Thank you
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people found this instruction helpful.
  • dicky from mcrae, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su re and disconnect power before starting!!
Was this helpful?
Thank you for voting!
large burners not working
0 of 2 people found this instruction helpful.
  • Greg from Versailles, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this helpful?
Thank you for voting!
The surface burner socket that the burner plugs into melted.
  • Gary from Chesapeake, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold t he socket, etc.
Was this helpful?
Thank you for voting!
Surface burner knob broke
  • Robert from Brimfield, MA
  • Really Easy
  • Less than 15 mins
Part was an exact replacement. Just aligned the knob with the stud on the range and gently press the replacement knob on.
Was this helpful?
Thank you for voting!
Burner keep coming on and going off had a short in burner plug-in block.
  • Judith from Staunton, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this helpful?
Thank you for voting!
Burner was slow heating at times. Moved back burner to front still same thing.
  • Gail M from Lockport, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this helpful?
Thank you for voting!
All Instructions for the 1765
31 - 45 of 60