147210 General Electric Range - Instructions

In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.

remove screws, re-install screws

In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer


This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!

I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.

I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

Pulled the gas stove out so that I could shut off the gas valve and unplug the power cord. Job was made easier by removing the oven door (which just slides out). I took the 2 screws out that held the old igniter in place. Went to the rear of the range where there was a small 3"X2" electrical cover for the igniter, and disconnected the wire leads from the wiring harness. I then pulled the old igniter out through the oven front. Fed the new igniter wires through the back of the range and plugged the new igniter in. Reinstalled the electrical cover in the back of the range, attached the 2 -1/4" screws to reinstall the igniter inside the broiler. Put back the oven door. Turned the gas valve back on and sprayed on a soapy solution to check for gas leaks. Plugged the electrical cord back in. Pushed range back in place, Turned broiler on. Wait for a few seconds till the gas comes back thru the line. Works great Our stove was a GE Profile Gas Range. The part number for the igniter is WB13K21. We are very satisfied. Jim

With the model number I wnet on Parts select site and located the part through the problem finder selection,(GREATFEATURE!) (74% the problem is the Flat Style Oven Igniter) (watched the video on installation and compared my unit with the one in the video). The video explained installation completely and made it very simple. The only critic is that the oven door can be removed completely to make it easier to get in the the oven, opening part way and lifting up the oven door will come completely off. Also the broiler pan drawer can be taken completely out if you would need to get in this way for some reason. Final note: I called the local GE dealer Parts dept- they would have had to order the part anyway and it would have cost three times what Parts Select charged me.Save $$$ great! .

Very was ti replace racks and knobs. Very fast mail service

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on

Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.

took nut driver to remove the old and replaced with new. simple.

Replaced the flat style oven igniter. First, I watched the video on your web site, and used it as a reference to make the repair. I did remove the oven door tho, as it made it easier to complete the work, the video didn't show the door being removed. The video was very helpful.