1456 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Blocks were broken
-
James J from Sweet Grass, MT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase..
... Read more
.parts arrived very timely...J. Iriwn
Read less
Was this helpful?
Thank you for voting!
replace end caps
-
Thomas from Glen Island, VA
- Easy
- Less than 15 mins
-
Screw drivers
The video was very helpful.Very easey repair
Was this helpful?
Thank you for voting!
Trim has tendancy to rust on range oven door
-
Carole from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unscrewed bottom screws, replaced trim. No trouble.
Was this helpful?
Thank you for voting!
Oven Door Handle End Caps.
-
Linda from Lake Panasoffkee, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I purchased my stove second hand. It was a mess but I saw a gem under all that dirt and grime. It took me a week and it looked brand new. The end caps on the oven door handle were discolored and cracked. They made the stove look old. It was an easy repair and my stove looks brand new. I will order an extra set just in case as these pa
... Read more
rts are getting harder and harder to find. I am so pleased with the original parts. They were here with in days and well before promised delivery date.
Read less
Was this helpful?
Thank you for voting!
Left bracket broken on range oven door handle.
-
Roger from De Soto, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portio
... Read more
n of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
Read less
Was this helpful?
Thank you for voting!
Burner was slow heating at times. Moved back burner to front still same thing.
-
Gail M from Lockport, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this helpful?
Thank you for voting!
The surface burner socket that the burner plugs into melted.
-
Gary from Chesapeake, VA
- Easy
- Less than 15 mins
-
Screw drivers
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold t
... Read more
he socket, etc.
Read less
Was this helpful?
Thank you for voting!
Burner keep coming on and going off had a short in burner plug-in block.
-
Judith from Staunton, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this helpful?
Thank you for voting!
burner not working
-
gene from kent, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
burner was shorting out replaced part works great
Was this helpful?
Thank you for voting!
burner would not heat up the connection was bad
-
Earl from Union Mills, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this helpful?
Thank you for voting!
Surface Burner not working
-
Cody from Abilene, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new b
... Read more
racket and installed the burner. double checked everything and lowered the top. Done
Read less
Was this helpful?
Thank you for voting!
Plastic end caps for oven door handle brokr off
-
Ben from The Hills, TX
- Really Easy
- Less than 15 mins
-
Pliers
When the replacement parts came (only took 2 days). I lifted the door off. Removed the screws that held the tempered glass front on the rest of the door. Removed the screws holding the broken end caps Replaced one end cap, inserted the handle, and fitted the 2nd end cap to the handle and screwed it in place. Screwed the front of the door
... Read more
to the back and replaced the door on its hinges. Easy as pie, ....Easier!
Read less
Was this helpful?
Thank you for voting!
End Cap broke on oven door.
-
Georgianna from Austin, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
It was easy as pie. Just followed the instructions.
Was this helpful?
Thank you for voting!
left end cap for oven door
-
Diane from Kingston, NY
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.
Was this helpful?
Thank you for voting!
stove burner no longer would heat up burner element
-
Bonnie from Price, UT
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.
Was this helpful?
Thank you for voting!