1452 - Instructions

The video was very helpful.Very easey repair

When the replacement parts came (only took 2 days). I lifted the door off. Removed the screws that held the tempered glass front on the rest of the door. Removed the screws holding the broken end caps Replaced one end cap, inserted the handle, and fitted the 2nd end cap to the handle and screwed it in place. Screwed the front of the door ... Read more to the back and replaced the door on its hinges. Easy as pie, ....Easier!

This installation was for a replacement for one of the burner bowls on the original order. Replacement bowl fits proiperly.

It was easy as pie. Just followed the instructions.

First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections per ... Read more iodically as to avoid another situation like this .

Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty eas ... Read more y fix.

Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.

repair was easy and the video was very good. My only problem, I had to go buy a tool, I did not have a nut driver.

Removed old part by removing the screws at the boottom of the oven door. I wasn't sure if the glass oven door cover would remain in place once the trim piece was removed, fortunately I was ready when it came down. The glass cover is large and heavy so you need to be ready to handle the bulk of this piece once the last screw is removed. ... Read more Cleaned everything and with the help of my wife, who secured the oven door cover in place, secured the new trim piece by replacing the screws. What a difference, looks like new! PartSelect provided great service in terms of speed and part acciracy.

Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. ... Read more Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!

I ordered the part, It came a few days later,,Within 15-20 minutes, I had it installed..Pretty easy...Thanks

Required removing the door, by sliding it off the hinges (open 1/4 then lift up), removing the outer frame which releases the inner glass door section exposing the door end screws. Removed the phillips head screw on each door end releasing the old handle. Inserted the new handle in the ends, screws replaced, reversing the above. Thank ... Read more s for the correct part. Byron C.

I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.

Replaced them all. Next I want to replace the burners.