14390 - Overview

Models starting with 14390

Click on the best match to narrow your results.

Parts for models starting with 14390

$29.65

Heat Resistant Adhesive

★★★★★

(1)

Part #W10841140

This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.

$16.37

Ceramic Fuse - 20 amp

★★★★★

(1)

Part #WPM0805101

This ceramic microwave fuse is just over an inch long. It is white in the center, while each end is made of metal. This is a twenty amp fuse.

$10.40

Dryer Screw

Part #WP90767

This screw is sold individually.

$10.95

Refrigerator Screw

Part #WP98165

This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.

$12.05

Range Hex Nut

Part #WP488130

Part may differ in appearance, but functions same as original.

$185.50

Agitator Assembly

★★★★★

(2)

Part #285574

Does not include softener dispenser. **** Some assembly required.****

2-Speed Drive Motor with Jumper Wire

Part #12002353

This two speed split phase washing machine motor performs 1725 revolutions per minute in one speed and 1140 revolutions per minute in the other speed. This motor runs at 1/2 horsepower and it carries 8.0 amps. It's a good idea to change your washer's belts at the same time as you replace this motor, as they may have become worn as well.

$15.39

Refrigerator Screw

Part #WP489464

Sold individually.

$6.95

Gasket-intake

Part #27355S

This is an authentic manufacturer sourced replacement part designed for use with a variety of lawn and garden equipment. This carburetor intake gasket which provides an air tight seal for the carburetor. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

$20.95

Gasket-engine Base

Part #691569

This is an original Briggs & Stratton replacement part. The engine base gasket is designed by the manufacturer for use in engines. This part is made of flexible plastic, and is used to seal the connection between the engine base and the cylinder assembly. You may require a wrench when replacing this item. This product is sold individually.

$21.95

Gasket-crankcase Cover

Part #691311

$21.95

Gasket-cylinder Head

Part #692230

This is a special component which helps to provide a tight seal for the cylinder head. Over time it will wear out and it may begin to crack eventually requiring a replacement. Check the appropriate diagrams for your model to ensure the proper repair procedure. This high-quality gasket is made of durable material and is sold as an individu...Read more

Read less

Exact Part matches for your search term

BLK-HI LIMIT TO BROIL EL

This part number matches the current model number 14390

Part #14390

Common Symptoms of models starting with 14390

How this model fails, and the parts that fix it.

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Agitator wasn't spinning well

26 of 31 people found this instruction helpful.

Nora from Marshall, TX
Really Easy
Less than 15 mins
Socket set

First I removed the screw that held it in place with a socket. The agitator became loose and easy to remove at this time so I lifted it from the washing machine. I then just placed the new agitator in place and replaced the screw being careful not to do it too tight. The replacing of this part was an easy job and thanks to Part Select ... Read more

Read less

Was this helpful?

microwave oven blew fuse

27 of 43 people found this instruction helpful.

tad from tamarack, MN
Really Easy
Less than 15 mins
Pliers, Screw drivers

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th ... Read more

Read less

Was this helpful?

Motor Froze

22 of 28 people found this instruction helpful.

Matt from Oxford, GA
A Bit Difficult
1- 2 hours
Nutdriver, Pliers, Screw drivers

Make sure to release the springs and pulleys before you try to tackle the bolts that hold the motor base to the bottom of the washer. Mine were a bit rusty and took some force to break loose. Also it's a good idea to take pictures of how everything sits before you disassemble as the pictures in the repair kit are not very clear. Oth ... Read more

Read less

Was this helpful?