1405 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Switch was not working after a repairman had fixed something else
0 of 4 people
found this instruction helpful.
-
Jackie from Nova, OH
- Really Easy
- Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a
... Read more
single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Read less
Was this helpful?
Thank you for voting!
Stopped and would not restart / start.
-
Patricia from Duck, WV
- Really Easy
- Less than 15 mins
-
Screw drivers
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed
... Read more
the previous procedures to complete repair.
Read less
Was this helpful?
Thank you for voting!
burner would go red after a few mintes
-
richard from pottsville, AR
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
put it off a week before i worked on it but if you can replace a plug on a excord you can do this less than 5 mins
Was this helpful?
Thank you for voting!
Element burned out
-
Francis E from Harwich, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
Element burned out, ordered from Sears. Took over 2 weeks to get, originally sent wrong burner then shipped second one to wrong address. When I installed element I found that switch was also burned out . I ordered it from Parts Select & it was in the stove in 24 hours from the time I ordered it on line. Be assured I know where I will orde
... Read more
r my parts from now on
Read less
Was this helpful?
Thank you for voting!
Burner light was on all the time but burner was off.
-
Cliffford from Rochester, MN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replaced the burner switch.
Was this helpful?
Thank you for voting!
Burner control failure/unable to regulate temp.
-
ROBERT from SALCHA, AK
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time
... Read more
) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.
Read less
Was this helpful?
Thank you for voting!
could not control temp on burner
-
Ernie from Cameron, MO
- Really Easy
- 15 - 30 mins
-
Pliers
Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!
Was this helpful?
Thank you for voting!
Burner goes full hot at any setting
-
Ronald from Clinton, TN
- Easy
- 15 - 30 mins
-
Screw drivers
First, I turned off the power at the switch box. Moved the stove out (That was a problem, because I am 80 years young) Removed the back panel, and moved the wires one at a time to the new switch. Removed the selector, then removed the 2 screws holding the switch in. Installed the new switch installed the dial selector, turned the power
... Read more
back on, and checked the burner. It works as advertised!!!!! Moved the stove back to its original position, and got a hug from my wife. PHEW!!! Now I think I'll take a nap.
Read less
Was this helpful?
Thank you for voting!
Dryer door switch broken or burned out
-
James from Iota, LA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.
Was this helpful?
Thank you for voting!
Burner would go on and then turn off, repeatedly.
-
Robert from Tonawanda, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unplugged unit, removed plate behind control panel, removed 5 or 6 wire connectors, pulled off burner switch knob and removed 2 screws that holds switch in place. Reversed the procedure and was done.
Was this helpful?
Thank you for voting!
Light switch went bad
-
Joseph T. from Morgantown, WV
- Really Easy
- Less than 15 mins
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this helpful?
Thank you for voting!
light switch sticking
-
Paula from Rush, NY
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this helpful?
Thank you for voting!
Light did not come on (bad bulb!) on TC18KL
-
Louis from Beloit, WI
- A Bit Difficult
- Less than 15 mins
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged th
... Read more
e unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Read less
Was this helpful?
Thank you for voting!
Light switch in the refrigerator was faulty from the first day we installed the fridge.
-
Mary from Wasilla, AK
- Easy
- Less than 15 mins
-
Screw drivers
I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world whe
... Read more
re my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!
Read less
Was this helpful?
Thank you for voting!
No light in frig
-
Irene from Whitehall, MT
- Really Easy
- Less than 15 mins
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this helpful?
Thank you for voting!