1335 - Overview

Models starting with 1335

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid Switch – Part Number: W10820036
$33.28
In Stock
Lid Switch
★★★★★
★★★★★
(7)
Part #W10820036
Keep your washer or dryer running safely with this easy-to-install lid or door switch kit. It stops the machine from working when the door is open, helping prevent spills and accidents. Compatible with many models, this small but important part fits neatly inside your appliance and comes with everything you need for installation. Just unplug your machine, swap out the old switch, and you're good to go. It’s about 2.5 inches long and blends in with most interiors.
Heat Resistant Adhesive – Part Number: W10841140
$29.65
In Stock
Heat Resistant Adhesive
★★★★★
★★★★★
(1)
Part #W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.
Ceramic Fuse - 20 amp – Part Number: WPM0805101
$16.37
In Stock
Ceramic Fuse - 20 amp
★★★★★
★★★★★
(1)
Part #WPM0805101
This ceramic microwave fuse is just over an inch long. It is white in the center, while each end is made of metal. This is a twenty amp fuse.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
ELEMENT BAKE - RB147 – Part Number: WG02F05395
$135.45
In Stock
ELEMENT BAKE - RB147
★★★★★
★★★★★
(9)
Part #WG02F05395
This bottom oven bake element is designed for 30-inch electric ranges and ovens, delivering reliable and even heat for baking. Rated at 3000 watts and operating on 240 volts, it helps resolve common issues such as no heat, uneven heating, or a visibly damaged element. Installed at the base of the oven, it restores proper cooking performance when the original element fails. Always disconnect power before installation, and be sure to verify your appliance model to ensure proper fit.
Range Hex Nut – Part Number: WP488130
$12.05
Special Order
Range Hex Nut
Part #WP488130
Part may differ in appearance, but functions same as original.
Fluorescent Lamp/Bulb – Part Number: F26T8-CW-4
No Longer Available
Fluorescent Lamp/Bulb
Part #F26T8-CW-4
HINGE REG – Part Number: WG02L02131
No Longer Available
Blower Belt – Part Number: WP691371
$70.12
In Stock
Blower Belt
★★★★★
★★★★★
(3)
Part #WP691371
If your dryer isn’t drying clothes like it used to or making strange noises, this blower belt might be the fix. It connects the motor to the blower wheel, helping move air through the drum so clothes dry faster. Made to fit select Whirlpool models, it’s tough and reliable. Just unplug your dryer before installing and check your model number to make sure it’s the right part!
SWITCH INF.2600W - WB23M99 – Part Number: WG02F05772
No Longer Available
SWITCH INF.2600W - WB23M99
Part #WG02F05772
ELEMENT 8" 2400W - P1T23F – Part Number: WG02F05386
$140.65
In Stock
ELEMENT 8" 2400W - P1T23F
Part #WG02F05386
Leveling Leg – Part Number: WB2X8248
No Longer Available
Leveling Leg
Part #WB2X8248

Exact Part matches for your search term

Screw – Part Number: 1335
No Longer Available
Screw
This part number matches the current model number 1335
Part #1335

Common Symptoms of models starting with 1335

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid closes, switch wouldn't turn on machine.
31 of 47 people found this instruction helpful.
  • Kenneth from Wilmington, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Was this helpful?
Thank you for voting!
microwave oven blew fuse
27 of 43 people found this instruction helpful.
  • tad from tamarack, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
Was this helpful?
Thank you for voting!
Washer would fill up, wash, then stop
22 of 31 people found this instruction helpful.
  • Glen from Plano, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Was this helpful?
Thank you for voting!