1305 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Wen the dryer gets hot but dry anything when it runs and no air comes through the filter opening with the filter out
2 of 2 people
found this instruction helpful.
-
Willis from FORT WORTH, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
First diagnose the problem. No air coming out the exhaust or filter, things aren’t drying, you can’t hear the blower running.
Fuses or breakers are verified ok and on.
Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cab ... Read more le from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches.
Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt.
Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below.
After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot.
Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.
Fuses or breakers are verified ok and on.
Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cab ... Read more le from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches.
Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt.
Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below.
After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot.
Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people
found this instruction helpful.
-
Victoria from Roslyn Heights, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag
... Read more
ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Read less
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people
found this instruction helpful.
-
James from Richmond, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person
found this instruction helpful.
-
Victor from NORFOLK, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people
found this instruction helpful.
-
satyavenkata from Bentonville, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people
found this instruction helpful.
-
Rick from BETHESDA, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people
found this instruction helpful.
-
Daniel from TRENTON, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said.
... Read more
I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Read less
Was this helpful?
Thank you for voting!
leaking front door. loose seal.
3 of 9 people
found this instruction helpful.
-
Frank from SANTA ROSA, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Followed instructions, those were OK.
Dishwasher front still leaking
Dishwasher front still leaking
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people
found this instruction helpful.
-
Edward from Nanuet, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people
found this instruction helpful.
-
Andris from Sands Point, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right ... Read more fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Read less
Was this helpful?
Thank you for voting!
Dryer door switch broken or burned out
-
James from Iota, LA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.
Was this helpful?
Thank you for voting!
Stopped and would not restart / start.
-
Patricia from Duck, WV
- Really Easy
- Less than 15 mins
-
Screw drivers
1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed
... Read more
the previous procedures to complete repair.
Read less
Was this helpful?
Thank you for voting!
over fill water
-
ronnie from meriden, CT
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
replace the water valve
Was this helpful?
Thank you for voting!