Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
11 of 15 peoplefound this instruction helpful.
Dana from HAMMOND, IN
A Bit Difficult
1- 2 hours
Nutdriver, Pliers, Screw drivers, Socket set
Removed tank and drained old gas. Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner. Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again. Cleaned spark plug electrode. Reassemble
... Read mored, poured Sea Foam in the bottom of the tank and gave it a few pulls. Let Sea Foam sit for a while, then filled the tank with Premium. Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 peoplefound this instruction helpful.
Lise from CEDAR GROVE, NJ
Very Easy
Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
Refrigerator Light bulb went out
7 of 12 peoplefound this instruction helpful.
ANGELA from MEBANE, NC
Very Easy
Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 peoplefound this instruction helpful.
Alan from SAN MATEO, CA
Very Easy
Less than 15 mins
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Parts fit like a glove
2 of 3 peoplefound this instruction helpful.
Wayne from OOLTEWAH, TN
Really Easy
30 - 60 mins
Nutdriver, Socket set
Removed pull start assembly down to the crank. Installed motor housing, motor fan & rewind assembly. All went real good.
Removed old broken rewind starter (4 bolts); found the Model and Serial numbers; found Parts Direct and ordered new assembly; upon delivery, reinstalled with new Starter and hardware.
Was this helpful?
Thank you for voting!
had no instructions on how to remove old door hinge recepticle..
0 of 1 peoplefound this instruction helpful.
Douglas from Colrain, MA
Difficult
1- 2 hours
Screw drivers
After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the
... Read moretab. It was sooo easy once I found that. I repeated in on the other side.
Read less
Was this helpful?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
12 of 46 peoplefound this instruction helpful.
Alberto from PALMETTO BAY, FL
Really Easy
30 - 60 mins
Socket set
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
My Orders
