1230 Range - Instructions

All Instructions for the 1230
76 - 90 of 115

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
vent fan cloging up
0 of 1 people found this instruction helpful.
  • JAMES from McALESTER, OK
  • Really Easy
  • Less than 15 mins
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.
Was this helpful?
Thank you for voting!
Fan switch was broken internally.
0 of 1 people found this instruction helpful.
  • Charles from Santa Clarita, CA
  • A Bit Difficult
  • Less than 15 mins
  • Socket set
After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on th e end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.
Was this helpful?
Thank you for voting!
Filter needed replacement. Old one was falling apart.
0 of 1 people found this instruction helpful.
  • Sophie from Warrenton, VA
  • Really Easy
  • Less than 15 mins
Removed old filter, dropped in the new one.
(This really was not a "repair")
Was this helpful?
Thank you for voting!
Worn out stove top
0 of 1 people found this instruction helpful.
  • Redona from Roseville, CA
  • Really Easy
  • Less than 15 mins
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!
Was this helpful?
Thank you for voting!
Old grease filter had hole wore through
0 of 1 people found this instruction helpful.
  • Michael from Mountain Iron, MN
  • Really Easy
  • Less than 15 mins
Pulled the old one out & inserted the new one. Less than five minutes.
Was this helpful?
Thank you for voting!
Grease filter was torn and bent
0 of 1 people found this instruction helpful.
  • Brent from Rancho Santa Fe, CA
  • Really Easy
  • Less than 15 mins
I just lifted out old filter, and put in new one.
Was this helpful?
Thank you for voting!
Old filter couldn't be cleaned
0 of 1 people found this instruction helpful.
  • William from Goshen, NY
  • Really Easy
  • Less than 15 mins
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???
Was this helpful?
Thank you for voting!
rotten filter for down draft vent
0 of 2 people found this instruction helpful.
  • Craig from Ashburn, GA
  • Really Easy
  • Less than 15 mins
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Was this helpful?
Thank you for voting!
Needed to replace the grease filter!
0 of 2 people found this instruction helpful.
  • Colette from Annapolis, MD
  • Really Easy
  • Less than 15 mins
Followed the directions. Piece of cake!!
Was this helpful?
Thank you for voting!
The paint begin popping of my original grill. My son had a friend that said that he could remove the old paint and repaint for me. Unfortunately in the shuffle of a motorcycle performance shop the grill was lost. I have been trying to get help from Jenn-Aire since March and they just kept saying th
0 of 2 people found this instruction helpful.
  • Norma from Salisbury, NC
  • Really Easy
  • Less than 15 mins
Very simple for me!!! Open the box, uncover the new grill and lay it in its place.


Thank you so much!
Was this helpful?
Thank you for voting!
old yucky filter
0 of 2 people found this instruction helpful.
  • Diane from Flower Mound, TX
  • Really Easy
  • Less than 15 mins
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Was this helpful?
Thank you for voting!
old worn out wall vent cap.
1 of 5 people found this instruction helpful.
  • Jim from Brewton, AL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
removed old and replaced with new without difficulty.
Was this helpful?
Thank you for voting!
Broken hinge
0 of 2 people found this instruction helpful.
  • Don from Exchange, WV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Took the door apart and replaced the hinge, very easy
Was this helpful?
Thank you for voting!
Downdraft switch on the top of the JennAir inkoperative.
0 of 3 people found this instruction helpful.
  • Daniel from Fort Walton Beach, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I verified that there was current running to the switch.
Ordered a new switch,
Replaced the switch.
Had a little problem getting the oneway washers off the pegs but not much.
Saved the cost of a repair man and felt good about myself!
Was this helpful?
Thank you for voting!
The paint had chipped and peeled on the inlet grill
0 of 4 people found this instruction helpful.
  • Ann from Irvington, NY
  • Really Easy
  • Less than 15 mins
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Was this helpful?
Thank you for voting!
All Instructions for the 1230
76 - 90 of 115