12-1663-57-01 Tappan Wall Oven - Instructions

All Instructions for the 12-1663-57-01
106 - 120 of 190

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniter would glow but no gas would turn on
0 of 1 people found this instruction helpful.
  • Ronald from brockton, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed 2 screws to oven bottom
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal
Was this helpful?
Thank you for voting!
no flame
0 of 1 people found this instruction helpful.
  • joe from newport beach, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
removed the old igniter, installed the new one. 15 minutes, piece o cake!
Was this helpful?
Thank you for voting!
Had a problem igniting the gas.
0 of 1 people found this instruction helpful.
  • Danny from Bremerton, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.
Was this helpful?
Thank you for voting!
Oven was slow to light, strong gas smell, long time to reach set temperature
0 of 1 people found this instruction helpful.
  • Gary Warren from Alexandria, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.

It was a snap!
Was this helpful?
Thank you for voting!
My oven would glow, but wouldn't heat.
0 of 1 people found this instruction helpful.
  • Steve from Macomb, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
Was this helpful?
Thank you for voting!
Oven would not light; gas odor
0 of 1 people found this instruction helpful.
  • Emily from Conneaut, OH
  • Really Easy
  • 15 - 30 mins
  • Wrench (Adjustable)
This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repa ired our stove myself!
Was this helpful?
Thank you for voting!
Oven igniter failure
0 of 1 people found this instruction helpful.
  • Brett from Morgantown, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.
Was this helpful?
Thank you for voting!
Oven would not light..
0 of 1 people found this instruction helpful.
  • Jim from Oceanside, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...
Was this helpful?
Thank you for voting!
Would turn oven on, gas smell and would not light .
0 of 1 people found this instruction helpful.
  • Michael from Forest City, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!
Was this helpful?
Thank you for voting!
oven was slow on lite up
0 of 1 people found this instruction helpful.
  • BILLY from DUCKHILL, MS
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
removed bottom plate in oven removed three screws and cut two wires.
Was this helpful?
Thank you for voting!
oven would not light
0 of 1 people found this instruction helpful.
  • wayne from Washington, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
took off bottom pan in oven and replaced ignitor
Was this helpful?
Thank you for voting!
The oven wouldn't light or very slow to light
1 of 4 people found this instruction helpful.
  • Chris from Shunk, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the two screws, took out the old one and replaced the new one. It was very easy and the oven works great now. Thanks.
Was this helpful?
Thank you for voting!
wouldn't light.
0 of 1 people found this instruction helpful.
  • brett from newbury pk, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it , then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!
Was this helpful?
Thank you for voting!
Gas oven would take forever to light and would not relight if cooking temp was reduced
0 of 1 people found this instruction helpful.
  • John from Newmarket, NH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.
Was this helpful?
Thank you for voting!
oven took a long time to preheat
0 of 1 people found this instruction helpful.
  • Brad from Medina, NY
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice
Was this helpful?
Thank you for voting!
All Instructions for the 12-1663-57-01
106 - 120 of 190