119901 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burning electrical smell and "buzzing"
5 of 7 people
found this instruction helpful.
-
Louis from Beloit, WI
- Easy
- 15 - 30 mins
-
Screw drivers
I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block ... Read more clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.
Pulled the range top up, used a phillips screwdriver to remove the terminal block ... Read more clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.
Read less
Was this helpful?
Thank you for voting!
Electric stove burners working intermitantly.
4 of 4 people
found this instruction helpful.
-
Michael from St. Louis, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).
Was this helpful?
Thank you for voting!
I damaged surface element left kettle on without water in it
4 of 4 people
found this instruction helpful.
-
Kenneth from LANOKA HARBOR, NJ
- Really Easy
- Less than 15 mins
The repair was really easy. All I did was unplug the surface element and plug in the new one.
Other Parts Used:
Was this helpful?
Thank you for voting!
Sparks emitted at burner connection and burner does not work.
4 of 5 people
found this instruction helpful.
-
Doug from Puyallup, WA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink slee ... Read more ves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink slee ... Read more ves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.
Read less
Was this helpful?
Thank you for voting!
Front left burner would not shut off, then switch fried
5 of 8 people
found this instruction helpful.
-
connie from madison, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to.
... Read more
We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.
Read less
Was this helpful?
Thank you for voting!
Coroded drip pans
4 of 5 people
found this instruction helpful.
-
Lori from Old Town, FL
- Really Easy
- Less than 15 mins
Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.
Other Parts Used:
Was this helpful?
Thank you for voting!
Switches were going bad and making a popping sound and smoking.
4 of 5 people
found this instruction helpful.
-
Joshua from Homestead, FL
- Easy
- 30 - 60 mins
-
Screw drivers
Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair compa
... Read more
ny wanted $370. I did it in 45 min. for less than $100.
Read less
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people
found this instruction helpful.
-
Alan from SAN MATEO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
surface element burned out
3 of 3 people
found this instruction helpful.
-
Robert from SEEKONK, MA
- Very Easy
- Less than 15 mins
Simple Just plugged it in !
Was this helpful?
Thank you for voting!
Drip bowels needed to be replaced
3 of 3 people
found this instruction helpful.
-
Francine from OTEGO, NY
- Very Easy
- Less than 15 mins
I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 people
found this instruction helpful.
-
Daniel from Falmouth, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Read less
Was this helpful?
Thank you for voting!
Element would not heat up
3 of 3 people
found this instruction helpful.
-
david from BUCKEYE, AZ
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I couldn't explain how to do the job any better than your instructional video does. As long as you follow the video instructions you should have no problems.
Other Parts Used:
Was this helpful?
Thank you for voting!
Stove-top Burner intermittently shut off and on-wouldn't heat properly
3 of 3 people
found this instruction helpful.
-
George from New Bloomfield, PA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works
... Read more
great now!
Read less
Was this helpful?
Thank you for voting!
element had been damaged
4 of 7 people
found this instruction helpful.
-
Merle from Towanda, PA
- Really Easy
- Less than 15 mins
I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.
Was this helpful?
Thank you for voting!
Heating element for a frigidaire stove top broke
2 of 2 people
found this instruction helpful.
-
Rebecca from ASHEVILLE, NC
- Very Easy
- Less than 15 mins
Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.
Great company. Makes it easy for me order.
Was this helpful?
Thank you for voting!