119704 Kenmore - Instructions

All Instructions for the 119704
121 - 135 of 239

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
glo plug wouldn/t ignite
0 of 1 people found this instruction helpful.
  • William from Smyrna, DE
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took out the old (2 screws) put clip on wires and put the new part in. Simple
Was this helpful?
Thank you for voting!
oven would not ignight
0 of 1 people found this instruction helpful.
  • joseph from broadview heights, OH
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
followed posted repair procedure on Parts select site. . . straight forward and simple. . .
Was this helpful?
Thank you for voting!
Oven not heating and theres a smell of gas.
0 of 1 people found this instruction helpful.
  • Ken from Fresno, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks
Was this helpful?
Thank you for voting!
oven would not light
0 of 1 people found this instruction helpful.
  • Gerald from Scotia, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.
Was this helpful?
Thank you for voting!
oven slow to warm and gas smell
0 of 1 people found this instruction helpful.
  • JONATHAN from DEARBORN, MI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean i n there MUCH better.
Was this helpful?
Thank you for voting!
igniter replacement
0 of 1 people found this instruction helpful.
  • Brianna from Livonia, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
followed online instructions
Was this helpful?
Thank you for voting!
The oven igniter no longer worked
0 of 1 people found this instruction helpful.
  • Ralph from East Brunswick, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. Af ter that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.
Was this helpful?
Thank you for voting!
perheat light stayed on, oven never came on.
0 of 1 people found this instruction helpful.
  • john from snowflake, AZ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
followed the instructions that come with the part. very quick and easy.
Was this helpful?
Thank you for voting!
oven stopped lighting!!
0 of 1 people found this instruction helpful.
  • crystal from philadelphia, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
wonderful went perfect!!!
Was this helpful?
Thank you for voting!
Oven would not come on
0 of 1 people found this instruction helpful.
  • Jim from Merced, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than i t had for some time.
Was this helpful?
Thank you for voting!
The oven igniter would glow but the oven wouldn`t lite
0 of 1 people found this instruction helpful.
  • James from Circleville, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After finding your page and using your trouble shooting guide, it was easy getting the right part and the video helped a lot. Removed the over rack- removed two screws to remove the bottom- two screws to remove the burner. Clipped the two wires to the old igniter and removed the burner from the oven,removed the two screws holding the igni ter and installed new one. clipped the wires to length and renistalled the burner. Using the two wire nuts supplied put the wires togather and reinstalled the bottom. Everything went well lite first try with no poof sound. Just in time for Thanksgiving cooking. Got fast delivery of parts. Will uas again. Thanks Partselect.
Was this helpful?
Thank you for voting!
oven would not heat up.
0 of 1 people found this instruction helpful.
  • Paul from Warwick, RI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!
Was this helpful?
Thank you for voting!
oven would not light
0 of 1 people found this instruction helpful.
  • wayne from Washington, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
took off bottom pan in oven and replaced ignitor
Was this helpful?
Thank you for voting!
Time to replace filter.
0 of 1 people found this instruction helpful.
  • Kay from Port Hueneme, CA
  • Really Easy
  • Less than 15 mins
I took out the old filter and put in the new filter. I ran some water through it and it was done.
Was this helpful?
Thank you for voting!
Red light came on, needed a new one
0 of 1 people found this instruction helpful.
  • Joseph from Virginia Beach, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the old, installed the new one and finally figure out we had to press the reset button.
Was this helpful?
Thank you for voting!
All Instructions for the 119704
121 - 135 of 239