11931012790 Kenmore Canister Vacuum - Instructions

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

Poped the top; removed the front of dryer; removed the drum; replaced the rollers and clips, new belt, and new idler pulley. Cleaned out all the lint. Reinstalled all. It works perfect. Ordering the parts was easy and the assistance you give in diagnosing the problem was excellent.

Ordered a parts kit with belt, tensioner, rollers, & clips, but did not use. Unfortunately, the kit was not correct for this model, regardless of the sales reps assurances. The kit had two rollers, our unit has four. The belt tensioner was not even close to being the same. However, a thorough cleaning of the interior with vacuum and rag was done. Removed, cleaned, and lubed each of the four rollers and the tensioner wheel as well. Lubed with small amounts of sewing machine oil on the axles and light spray of silicone on plastic to plastic contact points. Voila! It's as quiet as new.

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

it was easy all the parts were the exact replacement

Remove the lint filter. Remove top without disturbing control wiring -- turn top on end but make sure it cannot fall. Unhook contacts on door switch. Remove screws hloding front panel and kick plate. Remove door hinge springs. Remove front panel and kick plate.Fish out old broken belt. Remove drum. Vacuum out all the lint. Reposition/replace pulley assembly and wheels. Place new belt around drum. Reinstall drum being careful to properly position the seal at rear. Prop up the drum with a suitable sized article to keep it in position temporarily - or have someone else hold it in position. Thread drive belt through pulley assembly per directions and put over drive hub. Manually turn drum to ensure proper belt and seal positioning. Put front panel back on. Turn drum while inspecting seal -- use putty knife to slip under seal if necessary to ensure its not folded under drum lip. Remove the prop holding up drum. Reinstall door hinges springs.Reinstall kick plate. Reinstall top.

Replaced belt,wheels,idler arm and drive motor.Used video instructions from PartSelect.Instructions are spot on.All replacement parts were correct ans fit like a clove.Orderinig was esaey.Staff was friendly and knowleable.Parts arrived quikly with out using next day service.I will use PartSelect in the future and recomend the company to my coworkers and friens.

Kit was easy to install and after making sure the drum gaskets were set right the noises ended.

Opened up the dryer and found that the belt broke. Came to this web-sight and was quickly directed to the correct part once viewing the schematics, and then watched the video. The day the parts arrived in the mail, I went to work and managed to get the drying working that night! Thank you for the parts, the video...made it very easy to complete. Sheral

After removing the bottom front panel using a putty knife to pry the upper left and right edges of the panel, I noticed that the long thin drum belt had broken. I went online to PartSelect, and using the Whirlpool model number, found the parts diagrams. Since the dryer is 20 years old, I decided to order the maintenance kit part# PS373087 which includes new idler wheels, retainer clips, and a tension pulley as well as the belt . I found a number of webpages that offer guidance in replacing the belt. Along with the instructions that came with the maintenance kit, I was able to do the repairs and have the dryer up and running in 30 minutes. Remember to remove the door springs before taking off the upper front panel. You only need to loosen the bottom screws on this panel. Leaving them in place helps to align and hold the panel when re-installing it.

After running the unit for a minute or so I removed the back of the dryer. Unable to locate the problem from this vantage point, I then removed the bottom kick plate. Using a small flash light, and turning the drum by hand I discovered that one of the support rollers had burned out the bearings. I went to this web site to see if I could still get parts for the unit. I found not only the part, but a full repair kit. Knowing all the parts would need to be replaced at some point, and that Mom could not afford a new unit I replaced everything. The parts did truly arrive in one day when they arrived I went back to your web site. I had seen instructional videos while looking for the repair parts. After watching the video I removed the dryer drum, removed the parts to be replaced (2 drum support rollers the belt tension roller, and belt) I replaced old with new cleaned entire unit reassembled and it is working like a champ thank you very much for all the parts, and info

Parts in the maintenance kit (other than belt) did not fit this old dryer. Top up and front off (door did not have to be removed) drum removed without any problems, pulley in back of dryer. Lots of lint removed, this dryer, must be at least 25 year old, runs great!!!

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

Took the back off of the dryer and diagnosed the problem. When I saw that the belt was broken I got online and looked for a place to find a replacement. Found Partselect.com and checked out their site and not only did I find the right parts but I also found a video detailing the repair. I purchased a maintenance kit (the belt, the wheels, and the hardware) and the next day my parts arrived and I was able to get the dryer back together in no time at all.

I assumed the drum belt has broken so without looking and tearing into the dryer first. I looked at the model number on parts select and the belt was $43.00. However the maintenance kit wihich included the belt, 2 wheel guides and belt tensioner was only $25.00. go figure. Ordered it and within 3 days it was at my front door. After opening the dryer I noticed the belt was intact. After removing the drum I notice heavy resistance on the motor. Thinking motor bearings were out! The internal motor heaters would drop out and than reset. Opened the fan shroud and found that a sock had fallin into the top lint screen opening and locked up the fan wheel with out the persons knowledge when the screen was than pushed back into place. Alot of work to find out something so simple. hilarious actually. What a relief that it was not the motor and since I had it apart I went ahead and put in the entire maintenance kit anyway. The whole ordeal toless than 1 hr.