110C92962200 Kenmore Washer Dryer Combo - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door catch would not latch
Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you
Parts Used:
-
Sidney from hilliard, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Parts Used:
-
Rick from Lennon, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable)
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Auto Dry Cycle would quit...timer stop 1/2 way
Watched the vidio. Removed back, swap out part shown and replaced. 10 minutes.......Ran test load, and then with wet clothes.......Worked like it should and a $20 part was way better than replacing a dryer..........
Parts Used:
-
David from Fallon, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
timer wouldn't move
-
Elmer from Prim, AR
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would'nr cycle.
-
Donald from Hillsboro, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat....at all.
Not noticing the break in the heat coil, I ordered two other minor parts, before ordering the heat coil. Less than 10 minutes to replace the old one, and now it works great! Thank you for your installation instructions and parts diagrams!
Parts Used:
-
Da from Dover, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no heat
took off back. unhooked 2 wires and a screw. replaced and done . put on back.
Parts Used:
-
jesse from MCLEANSVILLE, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Wrench (Adjustable)
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Burner Would Fire Off When You First Started Drying Cycle But Would Not Fire Anymore After That
I replaced the cycling thermostat but this did not remedy the problem and after further evaluation I determined that the secondary solenoid coil (hold/assist)had an open coil wire on the gas valve. This is best purchased as a set, primary coil and secondary coil, as it is less expensive this way.
Parts Used:
-
PAUL from MOORE, OK
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer took too long
-
david from cincinnati, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat up.
First I unplugged my dryer. (220v) I then layed the dryer on its front. I then proceeded to remove the back cover after removing the duct clamp. The two screws holding the Cycling thermostat was removed after the two wire connections were slipped off. I placed the new cycling thermostat in place and put everything back in place and behold...Heat! This was a simple job for even the somewhat clumsy repair person. Good luck and Thank you Partselect! P.S. my order was placed on Friday and it was on my doorstep Saturday morning.
Parts Used:
-
Jeffery from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer lens had melted
i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.
Parts Used:
-
DAVID from HOUSTON, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heavy clothes not dry
-
Gary from Tangent, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer had inconsistent heating.
After watching the video on your website and doing just a little troubleshooting on the components of the dryer (thermostats, heating coil, fuse) I determined this thermostat to be the problem. I ordered it from your site and had it in a few days. Took me only a few minutes to put it in and the dryer is working great now!
Thanks for all the helpful information on your site!
Thanks for all the helpful information on your site!
Parts Used:
-
Micheal from COLLINSVILLE, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door would not stay closed because metal latch piece was gone.
I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.
Parts Used:
-
Ian from Greeley, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch broken
The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.
Parts Used:
-
Wayne from Columbiana, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!