110C92962200 Kenmore Washer Dryer Combo - Instructions

PartSelect is great for providing parts as requested. Unfortunately, neither of the 2 parts I ordered were on my machine. My bad for not looking at the actual part instead of the description. A word to the wise!

The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.

I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.

Measured resistance on thermostats & heating element. Found thermostat open so ordered replacement part and heat again.

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme

Initially, i watched the how to do it instruction in the fix website to determine the complexity of repairs. The instruction built up my confidence. I ordered and recieved the grill amd the two new sensors. I placed the two new sensors into the new grill sensor slots. Then removed the old grill by unscrewing three screws. Connected the two sensors positioned the grill and screwed in the three screws put the lent stray in the grill and closed the dyer door. I have been a happy camper ever since. I saved the $75 home insurance fee plus maintenence installment. Thanks

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.

Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.

First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the part they broke!

So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.

Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.

Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.

Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.

Easy, right?

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!