- Home
- 110C61292012
- Instructions
110C61292012 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer hummed but drum wouldn't turn unless helped.
8 of 10 people
found this instruction helpful.
-
Leo from Ellicott City, MD
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part
... Read more
was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.
Read less
Was this helpful?
Thank you for voting!
Would not shut off when door opened, interior light would not come on.
8 of 11 people
found this instruction helpful.
-
Charles from Lake Mary, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Replacing the part was easy: unscrew the old one from the front of the dryer after opening door, disconnect and replace with new one. Getting to it was a bit more difficult: Remove 6 screws from the back, 4 that hold the back of the top down and 2 that hold the control panel in place. You had to remove the control panel to free up the w
... Read more
iring bundle (held in place by a tie wrap inside the control panel housing) so you could move the top forwards enough. Then remove the top of the dryer by lifting the back up slightly and moving it forward to disconnect from attachments in the front and move aside to gain access to the switch.
Read less
Was this helpful?
Thank you for voting!
handle broke on filter
7 of 8 people
found this instruction helpful.
-
Connie from Gaithersburg, MD
- Really Easy
- Less than 15 mins
just slide the new filter in.
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people
found this instruction helpful.
-
Joseph from Austin, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t
... Read more
o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Read less
Was this helpful?
Thank you for voting!
Dryer air would not heat
7 of 8 people
found this instruction helpful.
-
Jacqulyn from ANDERSON, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Boyfriend stated it was simple, he removed the back and replaced the part using a few everyday tools.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud screeching noise when dryer running
6 of 6 people
found this instruction helpful.
-
Stephen from Charlotte, NC
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First, removed the bottom cover below the dryer door. This is just held on with two clips that can be pushed in with a flat screw driver. Then remove the springs that go from the bottom of the dryer to the inside of the dryer door. We had to remove the entire front of the dryer, so the easiest way we found was to loosen the two screws
... Read more
on the bottom of the front panel, but not remove them. Then pop up the top of the dryer. To lift the top, first remove the two screws under the little door where the lint trap goes. The top is hinged in the back, and it snaps down onto two clips that can easily be popped up with a flat screw driver) With the top opened, there are two screws accessible. When the front of the dryer is removed, there will be nothing to support the drum, so what we found was that if you rotate the drum, you'll find a point where there's a hole in the top of the drum. If you take the springs that you removed from the bottom of the door you can hook them into this hole, and hook the other end into a hole in the back wall of the dryer just behind the drum. The springs are the perfect size for this, and it keeps the drum from falling when you remove the front panel. then just disconnect the three wires going to the switch inside the front panel, and remove the two screws from the top of the front panel. It should then lift right off. The bearing can just be pulled away and the new one installed. Put everything together again in reverse order.
Read less
Was this helpful?
Thank you for voting!
Loud Noise While Drying
7 of 9 people
found this instruction helpful.
-
John from Metamora, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!
john
john
Was this helpful?
Thank you for voting!
Dryer making squealing noise.
8 of 12 people
found this instruction helpful.
-
Harriet from Palm Coast, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up.
... Read more
Replaced front and top.
Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lens melted because paper got behind the lens and was heated by the lamp.
6 of 6 people
found this instruction helpful.
-
Chris from Valley Stream, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
1 screw to replace.
Was this helpful?
Thank you for voting!
Dryer would stop after a very short time when cold, wouldn't keep running at all when hot
6 of 6 people
found this instruction helpful.
-
Paul from ANTIOCH, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
At first I was advised to replace the temperature overload sensors, which I did but didn't fix the problem. After adding the additional information that the dryer would run to full cycle as long as the Start switch was held in I was advised to replace the Start switch.
It wasn't obvious from the wiring diagram, but if you remo ... Read more ve the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.
The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.
Thanks for your help PartsSelect!
It wasn't obvious from the wiring diagram, but if you remo ... Read more ve the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.
The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.
Thanks for your help PartsSelect!
Read less
Was this helpful?
Thank you for voting!
Needed to repair and replace dryer motor pulley and pully
6 of 6 people
found this instruction helpful.
-
Rob from GAITHERSBURG, MD
- Really Easy
- 30 - 60 mins
-
Wrench (Adjustable)
this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the comp
... Read more
any was a perfect fit.
Read less
Was this helpful?
Thank you for voting!
Dryer making a rumbling sound
8 of 13 people
found this instruction helpful.
-
Michael from Jacksonville, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.
Was this helpful?
Thank you for voting!
drum stopped rotating - broken belt
7 of 10 people
found this instruction helpful.
-
lisa from manteca, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.
Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new
Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new
Was this helpful?
Thank you for voting!
No heat in dryer and lint filter torn
6 of 7 people
found this instruction helpful.
-
Gerard from Huntington, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Dryer didn't heat. I got the heating element thru sears and when I ordered it I thought I should also order the thermostats but I didn't. Element arrived two days after ordered right on time. Slipped right in in a few minutes. Turned dryer on. No heat. Went back to drawing board. Watched videos on part select site and realized I needed th
... Read more
ermostats. Ordered them and lint filter. Arrived right on schedule and also slipped in in no time flat. Turned dryer on and yes it heated perfectly. Wife was pretty impressed with new lint filter as other one was torn with jagged edges. MY SUGGESTION: if your dryer doesn't heat and you can't test each individual item thermostats and heating element order the three of them ( high limit and cycling thermostats and heating element) cause they'll probably will all go at the same time anyway. Then won't have to wait on the second shipment if things don't work with partial replacement. Parts select was great and videos are well understood and easy to follow. Would certainly use again.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud, low-pitched thumping noise
7 of 10 people
found this instruction helpful.
-
Joseph from SKANEATELES, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First, let me say the t videos are excellent. Check them out if you haven't already.
I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.
I took a chance and ordered the maintenance kit to avoid having to take the dryer part ... Read more to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .
Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.
Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.
As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.
It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.
One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)
It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.
I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.
I took a chance and ordered the maintenance kit to avoid having to take the dryer part ... Read more to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .
Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.
Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.
As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.
It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.
One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)
It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.
Read less
Was this helpful?
Thank you for voting!