110C61102011 Kenmore Dryer - Instructions

The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a repair kit!

Removed two screws from lint trap and pried front of top up gently. Top hinges backwards which is convienent. Two more screws take the front off. Removed drum and old parts. Removed rollers etc. Per the instructions. Cleaned inside of unit with a shop vac.

Reassemble unit and test. Nice and quiet again and working well. Great service fro. Partselect.com.

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.

unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.

I did my repair alone by myself after viewing a short video online at partselect.com The man in the video showed every step slowly and professionally. I took some extra time to clean the dust off behind the back of Dryer while I had it open for fixing.....thanks for your help and it saved me over $190 plus which I was quoted by technician for estimate and parts. I paid $43.00 for my parts...both High limit and Cycling thermostats were replaced. My wife told me good job honey ! You can do it too.

Installed thermal cut-off kit. Dryer works fine now. Kit very easy to install.

As seen in video, All Good !

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.

Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waited 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.

Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.