110C6 Kenmore Dryer - Instructions

After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece i ... Read more n the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!

1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)

After realizing that my dryer was no longer heating, I took off the back and examined the heating element. I saw that a coil was broken and knew that it needed replaced. When the part came in, I basically changed out the wires that were plugged into the old element on to the new one, replaced the screws in the heating element housing an ... Read more d back panel, plugged in the dryer and was back in business! Oh, by the way...I am a 49 year old WOMAN!!!!

First unplug your dryer. Then, I removed the two screws on the lint trap leaving the lint trap in place--do not pull out the lint trap--only remove the two screws. Next, slide the top of the dryer slightly forward in order to release the top of the dryer. I did this with my hands. Once the top of the dryer is released, raise the top of t ... Read more he dryer and unplug the door switch assembly. Then, remove the two screws that hold the switch. These two screws were located on the front panel of my dryer and are visible when you open the dryer door. Remove the old switch and install the new switch by putting the two screws you previously took out from the old switch back in place and plug in the new switch. Lower the dryer top. Push the top back to lock in place. Line up the lint trap holes for the two screws that hold it in place and replace those screws. Plug your dryer back in and it should work properly. Very easy repair. We ordered our part one morning before noon, and it was here the next afternoon with regular shipping. GREAT SERVICE.

I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I h ... Read more ad also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan

The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re ... Read more move and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.

Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power.

This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door ... Read more was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10 ... Read more year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.

Unplug from the wall ,remove upper back panel ( watch out for the grounding wire screwed to the panel), pulled off front knob, then twist and pull the switch out. Unplug the burned out switch, plugged in the new one. Re-assembled what I took apart, plugged her up and dried the load that was in the washer. Note: if yours is burned out due ... Read more to house power surge make sure the timer is working after you replace the switch, you might need one of thoes too.

I purchased the dryer repair kit with the drum belt, wheels and idler pulley. I watched the instructional videos online and it seemed fairly straight forward. Breaking down the dryer and replacing the pulleys was easy enough. My problem began when I tried to feed the drum belt around the idler pulley. After finishing the job, the dryer wo ... Read more uld not turn and the sensor light stayed on. I thought something else was broken with the dryer and spent hours trouble shooting other problems that I was having. Finally I figured out that the drum belt was not installed correctly around the idler pulley. However, I could not get it properly installed from the front of the machine so I tried from the rear still with no avail. I finally had to fish the old belt out of the garbage can that I had thrown away earlier. I lined up the old belt with the new one in the kit and discovered that the new belt was much smaller, so I put the old one back on the drum. Here's the lesson I learned...make sure the belts are the same size before attempting to install. The old idler was responsible for the squeaking and that stopped but I am still using the same old drum belt. Hope it lasts.

couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! ... Read more Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!

1st Unpluged power.
2nd removed two screws under lint screen cover.
3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel
4th removed drum
5th took out plastic triangle wheel rings
6th removed old belt guild (to motor pully)
... Read more />7th removed old wheels and plastic rings stops
8th cleaned excessive hair dust with shopvac
9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.
10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.
JUst like a new dryer aain after all PM was complete.

Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer ... Read more ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.

Removed front panel, drum,replaced belt,tensioner and worn rollers. Then removed rear panel and replaced heating element and high limit thermostat. While I was there completely cleaned inside of dryer. Repair and replacement of parts was quite easy. Just take your time and don't hurry it.