11097593 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Our dryer started squealing and would then stop running.
55 of 69 people
found this instruction helpful.
-
Kelly from Aptos, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The par ... Read more t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The par ... Read more t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't turn on
49 of 64 people
found this instruction helpful.
-
Olive from Williamsburg, OH
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
Read less
Was this helpful?
Thank you for voting!
TOb stopped turning after a week or so of high pitched "squeals" coming from inside the dryer.
43 of 48 people
found this instruction helpful.
-
Robert from Princeton, WV
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as
... Read more
the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.
Read less
Was this helpful?
Thank you for voting!
Gas Flame Would Drop Out
49 of 66 people
found this instruction helpful.
-
FRED from BRIELLE, NJ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this helpful?
Thank you for voting!
Dryer would not shut off on auto dry settings
42 of 50 people
found this instruction helpful.
-
Wiliam from Belleville, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.
Was this helpful?
Thank you for voting!
worn out part
44 of 64 people
found this instruction helpful.
-
John from Tucson, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people
found this instruction helpful.
-
Bill from Houston, TX
- Really Easy
- Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people
found this instruction helpful.
-
Robert from GOODRICH, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel.
... Read more
The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Read less
Was this helpful?
Thank you for voting!
Dryer not spinning
33 of 49 people
found this instruction helpful.
-
john from goldsboro, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into
... Read more
place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Read less
Was this helpful?
Thank you for voting!
had to replace the motor
31 of 43 people
found this instruction helpful.
-
charles from parker, CO
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the n
... Read more
ew box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.
Read less
Was this helpful?
Thank you for voting!
Dryer would not heat up.
26 of 30 people
found this instruction helpful.
-
Roger from Bonners Ferry, ID
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the f
... Read more
ront open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Read less
Was this helpful?
Thank you for voting!
Felt piece coming out of filter
27 of 33 people
found this instruction helpful.
-
Sara from Solon, IA
- Really Easy
- Less than 15 mins
Removed old filter and put in new one.
Was this helpful?
Thank you for voting!
noisy drum
29 of 40 people
found this instruction helpful.
-
Jeff from Mesa, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
Lid closes, switch wouldn't turn on machine.
31 of 47 people
found this instruction helpful.
-
Kenneth from Wilmington, IL
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams.
... Read more
Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Read less
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people
found this instruction helpful.
-
joe from cheswick, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!