1109728 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer worked but no heat
18 of 20 people
found this instruction helpful.
-
Tracie from Culver City, CA
- A Bit Difficult
- 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem
... Read more
was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Read less
Was this helpful?
Thank you for voting!
Insanely loud squeaking
17 of 17 people
found this instruction helpful.
-
Stacy B. from MUKWONAGO, WI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
With the correct parts and watching the video, it was so easy to repair. We ordered the wrong part (for the Electric Dryer when it should have been for the Residential Dryer) but the return was easy and we got the new parts super fast. Next time I would probably look at the offending part first before ordering just to make certain. But w
... Read more
e used a socket set and Philips screwdriver and actually had our teens do all the work for experience. Fixed the loud noise one and for all.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Replaced two parts in the gas heater assembly
20 of 26 people
found this instruction helpful.
-
L R from Carmel, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with th
... Read more
e new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer drum was not turning when started.
17 of 18 people
found this instruction helpful.
-
Dennis from AUSTIN, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I moved the dryer to a location where I could get to both the front and back sides. I opened the back by first removing the top cover and then the back. It requires either a Phillips head screwdriver or a quarter inch socket. In addition, it requires removing the four power wires which connect to the computer. If you are unfamiliar with t
... Read more
he wiring layout, take a photo with your cell phone which you can then refer to when re-assembling. Once the back was removed, I saw that the belt was still intact, but the pulley which provides tension to the belt was frozen. Take a photo of the belt route between the motor and the pulley. Try to get the spring position in the photo. Remove the belt from the pulley by reducing the tension and then sliding the belt out (this assumes the belt is not broken). The pulley arm is held in place by a single bolt which can be removed by a socket set. Remove the arm with the pulley attached. Examine the pulley to figure out why it is frozen. In my case, the pulley had been frozen for some time and the belt had actually chewed through the pulley and was sliding (polishing) on the pulley axle? I used a pair of pliers to loosen the destroyed pulley by rotating it back and forth over the axle while gripping the arm the axle is attached to. As it loosened up I worked it off the axle. I used a cloth to clean the axle of grime from the belt, pulley, and dryer lint. The new pulley comes with a washer and triangular plastic "fastener". First you put on the washer, then the pulley and then you secure it on the axle by sliding the triangular fastener over the axle so it sits in a small grove near the end of the axle. Then put the pulley arm back by replacing the bolt. Make sure you do not overtighten the arm since it is intended to rotate about the bolt. If the dryer belt breaks, the spring will pull the arm down and throw a cutoff switch. Its operation should be obvious. Once the arm is back in place, refer to your photo and replace the spring (this can be tricky and frustrating, particularly if you don't use something like needle nose pliers). Once the spring is in place, depress it and re-install the dryer belt. Refer to the photo you took earlier if you've forgotten how the belt was routed. Then re-install the dryer's back panel, re-attach the electric wires (again refer to the photo you took earlier), and re-attach the top cover. You might want to test your handiwork at this point before you reconnect the dryer vent
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Dryer would not start
17 of 18 people
found this instruction helpful.
-
Dennis from Redondo Beach, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First and most important was to unplug the unit.
I removed the 2 screws that hold the lint screen shoot to the top cover and then simply popped the top of the machine open using 2 screw drivers and
gently prying it up. I raised the top cover about 8 inches and supported it with a block of wood.
I opened the front loading do ... Read more or and removed the 2 screws that hold the door actuator switch while holding the switch on the inside so that nothing would fall down into no mans land. Once the switch was loose I pulled it into view and could see that the actuator spring was broken. I used the search at the Part Select Web site and found the placement part very easy. I was amazed that the part was shipped and delivered to my house the very next day. The actuator spring simply snaps into place and I assembled it in the reverse order of removal, I removed the block of wood and snapped the top back into location and reinstalled the 2 screws for the lint screen shoot . I plugged the dryer in and it work perfect. I can't say enough about how well the experiance with Parts Select went, I will recommend them to others.
I removed the 2 screws that hold the lint screen shoot to the top cover and then simply popped the top of the machine open using 2 screw drivers and
gently prying it up. I raised the top cover about 8 inches and supported it with a block of wood.
I opened the front loading do ... Read more or and removed the 2 screws that hold the door actuator switch while holding the switch on the inside so that nothing would fall down into no mans land. Once the switch was loose I pulled it into view and could see that the actuator spring was broken. I used the search at the Part Select Web site and found the placement part very easy. I was amazed that the part was shipped and delivered to my house the very next day. The actuator spring simply snaps into place and I assembled it in the reverse order of removal, I removed the block of wood and snapped the top back into location and reinstalled the 2 screws for the lint screen shoot . I plugged the dryer in and it work perfect. I can't say enough about how well the experiance with Parts Select went, I will recommend them to others.
Read less
Was this helpful?
Thank you for voting!
idler pully sqwieling
19 of 24 people
found this instruction helpful.
-
Jerry Duty from Fort Walton Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!
and your done !!!
Was this helpful?
Thank you for voting!
The felt strip on the filter had come undone.
21 of 31 people
found this instruction helpful.
-
Rebecca from Laredo, TX
- Really Easy
- Less than 15 mins
Took the old filter out and inserted the new one- works great!!
Was this helpful?
Thank you for voting!
Dryer starts with loud squeak initially. Eventually there was a loud clank and dryer stopped.
16 of 17 people
found this instruction helpful.
-
Victor from HOUSTON, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Rather than remove the front panels, door, control panel and drum, I noticed 1/4" metal screws on the back panel. There were approximately 6 holding the back panel in place. I did have to remove the top panel as well before removing the back. Once removed I had complete access to the broken idler pulley assembly. I immediately saw the b
... Read more
roken pulley. I installed the new one with very little effort. Reset the belt according to instructions from the video. Reassembled, plugged in, hit start and enjoyed the sweet sounds of success. All told it took me about 20 minutes from start to finish.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 people
found this instruction helpful.
-
Xiaobin from Cordova, TN
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.
Was this helpful?
Thank you for voting!
Washer will agitate, but won't spin
18 of 24 people
found this instruction helpful.
-
Mandie from Lewisville, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.
I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.
The swit ... Read more ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.
After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.
Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.
The swit ... Read more ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.
After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.
Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
Read less
Was this helpful?
Thank you for voting!
part number was different from the original, but it fit just fine.
20 of 30 people
found this instruction helpful.
-
John from Bristol, CT
- Easy
- Less than 15 mins
installed the new dryer lint screen, it fit perfectly
and is now in operation.
and is now in operation.
Was this helpful?
Thank you for voting!
Rear Drum seal wore out, and needed to be replaced.
14 of 14 people
found this instruction helpful.
-
David from San Jose, CA
- Easy
- 1- 2 hours
-
Screw drivers, Socket set, Wrench set
I thought this repair would be a lot harder than it was. First I removed the top of the dryer ( removed two screws from the backside) then I removed the frontside of the dryer( i think two or four screws) just look along the edges to see where it's attached. Then I also removed the lower panel of the front of the dryer The one with clips
... Read more
to secure on the dryer. Removed the ground wire from panel. I removed the screws that holds on the lint vent and took that off. I easily took the drum out of the dryer and then placed it on the floor with the backside facing up. I then removed the damaged old felt strip (which had been glued on) I sanded a little to remove some of the residue. I checked the instructions to make sure I placed the new belt on correctly, and then glued it to the drum.(Note; the belt I received was too big about 3". I just cut it and sewn it together. It fit perfectly after that.) If this is a problem for you I don't think it has to be sewn because the glue you use to secure it holds tight and dries fast.
I also inspected and touched up the front felt seal with the glue.
After it dries about 10-15 min, I put the drum back in the dryer and then reattached the dryer vent and the front panel. I took a look at the instructions to set the back felt belt correctly. I turned the drum, gently pull the edge of the felt seal to the surface. After that I set the dryer belt up. This was bit tricky, I had to reach from the bottom panel area and after a few trys I got it . ( When setting the dryer belt, It works better if you push the spring arm with your hand instead of trying to use the belt to pull it toward the motor) Then I turn the drum a couple of times to make sure it was on good. then I put the bottom panel on and then the top back on and I was good to go. It works great now.
I also inspected and touched up the front felt seal with the glue.
After it dries about 10-15 min, I put the drum back in the dryer and then reattached the dryer vent and the front panel. I took a look at the instructions to set the back felt belt correctly. I turned the drum, gently pull the edge of the felt seal to the surface. After that I set the dryer belt up. This was bit tricky, I had to reach from the bottom panel area and after a few trys I got it . ( When setting the dryer belt, It works better if you push the spring arm with your hand instead of trying to use the belt to pull it toward the motor) Then I turn the drum a couple of times to make sure it was on good. then I put the bottom panel on and then the top back on and I was good to go. It works great now.
Read less
Was this helpful?
Thank you for voting!
seal for lint filter came off
17 of 23 people
found this instruction helpful.
-
John from Midland, TX
- Really Easy
- Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!
Door catch on dryer door broke
14 of 14 people
found this instruction helpful.
-
Lynne from Jamestown, CA
- Really Easy
- Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c
... Read more
ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Read less
Was this helpful?
Thank you for voting!
Change dryer belt
15 of 17 people
found this instruction helpful.
-
Scott from Bayport, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I p
... Read more
opped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.
Read less
Was this helpful?
Thank you for voting!