110964 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer runs but no heat
191 of 265 people
found this instruction helpful.
-
Todd from Roswell, GA
- Easy
- 15 - 30 mins
-
Socket set
unpluged the dryer, removed the back panel, I examined the heating coil, it seemed unbroken, so I used a amp meter to test the various sensors. Found the upper thermal sensor was bad, looked up the part and ordered it, had to get the thermal cut off kit to get the sensor I needed. Installed it no problem, put the back back on, and it work
... Read more
ed great.
Read less
Was this helpful?
Thank you for voting!
no heat
163 of 182 people
found this instruction helpful.
-
kat from powell, OH
- A Bit Difficult
- 30 - 60 mins
-
Socket set
First, I replaced the heating element which was super easy but I still didn't have heat - frustrating! I then ordered the thermal cut-off kit and thermal fuse. I replaced the thermal fuse and still no heat. Then, I took one of the fuses from the kit and replaced that and finally got heat. There was another fuse in this kit that I still do
... Read more
n't know where it goes but right now I don't need it. Had I known (by a volt tester) this would have been super easy to fix, but I didn't have one so it was trial and error. I did find out, however, that if the heating element goes it usually takes the fuse with it. The fuse I replaced (that finally gave me heat) was located in the casing just above the element. I hope this helps!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Squeaky dryer
155 of 167 people
found this instruction helpful.
-
CHRISTOPHER from MOUNT AIRY, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
My wife had been complaing about excessive noise from our 25 year old dryer so after DISCONNECTING the dryer from the wall outlet I popped the top panel loose @ the front with a screw driver @ each front corner @ took a look. No cause was visible so I removed the rear cover & still nothing so I laid the dryer on it's back to remove the fr
... Read more
ont cover. First the 2 wires to the door switch were disconnected then the 2 screws @ the top corners that hold the front panel to the side panels were removed. The front panel then slid up & lifted off exposing the front of the drum, belt & support pulleys. Upon inspection I found the bottom support pulley sleeve bearing to have worn out. Both pulleys were replaced because they only come as a pair now along with the tensioner pulley (idler pulley), the belt & the rear lip seal on the drum since it had a 4" section missing from the edge @ one point (all of these were the original components). Replacing the rear drum seal took the most time because the old adhesive had to be removed. I did this first so the glue could set while I installed the new pulleys & belt. By the time they were installed, the glue had set enough & I could continue the re-assembly.
We now have a 25 year old dryer that sounds like it's new & @ a fraction of the cost
We now have a 25 year old dryer that sounds like it's new & @ a fraction of the cost
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
broken tumbler belt
145 of 165 people
found this instruction helpful.
-
Michael from San Antonio, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
Read less
Was this helpful?
Thank you for voting!
dryer door would not stay shut
103 of 107 people
found this instruction helpful.
-
Pam from Woodbridge, VA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door
... Read more
was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.
Read less
Was this helpful?
Thank you for voting!
Dryer was not heating
100 of 109 people
found this instruction helpful.
-
Frank from Fort Collins, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This is the second heating element I have replaced in this dryer which I bought new in 1977. That's right it is 32 years old and still works great!
The replacement process is simple:
One: pull the dryer away from the wall so that you have room to work in the back.
Two: Disconnect the dryer vent hose from the back of t ... Read more he dryer.
Three: Remove the five - 5/16" hex head sheet metal screws that hold the back cover in place and set the cover to the side.
Four: Go to the front of the dryer and remove the lint filter and the two slot head screws that hold the lint filter opening to the internal frame.
Five: Pop the top of the dryer open and remove the one 5/16" hex head screw that holds the top of the heating element strap to the frame.
Six: Go to the back of the dryer and remove the two leads from the thermostat that is mounted to the heating element casing. CAUTION: Be careful to note the position of the wires and be certain that you reattach the correct wire to the correct lead.
Seven: Lift the heating element case up about 1/2" to disengage the hooks at the bottom that hold it in place.Then pull the bottom of the heating toward you slightly while sliding it down. This will allow you to remove the heating element and casing.
Eight: Remove the heating element from the casing and insert the replacement heating element.
Reverse the above process to reassemble.
This entire process only takes about 20 minutes.
An additional note: Be certain that you pay careful attention to the positioning of the strap that holds the top of the heating element case to the dryer frame. If you install it incorrectly, the heating element case can fall away from the back of the drum assembly.
The replacement process is simple:
One: pull the dryer away from the wall so that you have room to work in the back.
Two: Disconnect the dryer vent hose from the back of t ... Read more he dryer.
Three: Remove the five - 5/16" hex head sheet metal screws that hold the back cover in place and set the cover to the side.
Four: Go to the front of the dryer and remove the lint filter and the two slot head screws that hold the lint filter opening to the internal frame.
Five: Pop the top of the dryer open and remove the one 5/16" hex head screw that holds the top of the heating element strap to the frame.
Six: Go to the back of the dryer and remove the two leads from the thermostat that is mounted to the heating element casing. CAUTION: Be careful to note the position of the wires and be certain that you reattach the correct wire to the correct lead.
Seven: Lift the heating element case up about 1/2" to disengage the hooks at the bottom that hold it in place.Then pull the bottom of the heating toward you slightly while sliding it down. This will allow you to remove the heating element and casing.
Eight: Remove the heating element from the casing and insert the replacement heating element.
Reverse the above process to reassemble.
This entire process only takes about 20 minutes.
An additional note: Be certain that you pay careful attention to the positioning of the strap that holds the top of the heating element case to the dryer frame. If you install it incorrectly, the heating element case can fall away from the back of the drum assembly.
Read less
Was this helpful?
Thank you for voting!
Make humming noise when pressing start button. Would not start
98 of 112 people
found this instruction helpful.
-
James from Moscow, IA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10
... Read more
year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.
Read less
Was this helpful?
Thank you for voting!
door switch actuator spring broken
92 of 100 people
found this instruction helpful.
-
Paul from Vero Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located o ... Read more n upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located o ... Read more n upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife
Read less
Was this helpful?
Thank you for voting!
Bought motor, then bought blower wheel also
95 of 111 people
found this instruction helpful.
-
Daniel from Coatesville, PA
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Wrench (Adjustable)
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw!
... Read more
Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
Read less
Was this helpful?
Thank you for voting!
Broken belt - drum would not turn
87 of 101 people
found this instruction helpful.
-
Gary from Oakland, MD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer
... Read more
ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.
Read less
Was this helpful?
Thank you for voting!
Door won't latch
95 of 158 people
found this instruction helpful.
-
Jill from bellevue, WA
- Really Easy
- Less than 15 mins
-
Pliers
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks
Was this helpful?
Thank you for voting!
Replacing worn drum support rollers and shafts.
60 of 69 people
found this instruction helpful.
-
Gary from Canton, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Very easy once I figured out how to open it up to see what was the matter.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the ... Read more front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.
Good luck, It s not as bad as it sounds.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the ... Read more front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.
Good luck, It s not as bad as it sounds.
Read less
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people
found this instruction helpful.
-
RONALD from SALMON, ID
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!
the dryer only blew cold air
48 of 52 people
found this instruction helpful.
-
charles from waukesha, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
Was this helpful?
Thank you for voting!
Dryer quit heating.
46 of 53 people
found this instruction helpful.
-
Jo from BANDON, OR
- Easy
- More than 2 hours
-
Pliers, Screw drivers, Socket set
This dryer is 30 plus years old. I am a 71 year old female that has never taken on this type of repair. First I very carefully ordered all parts possibly associated with this problem. Watched all videos available for this model. Could not find one at Parts Select that addressed this particular dryer. Model number was correct. Finally
... Read more
found YouTube video that addressed an "Old Kenmore Wood Top". It showed the correct way to remove the Heating Element unit. Also Parts Select never mentions that fuses and sensors are not "polarized". Very important info for a novice. But Google helped me with that. Heating Element is "polarized", very important not to cross wires. I did order a couple Heating Element Connection Wire Kits that were not needed for this repair. Got all parts replaced, put dryer back together, crossed my fingers and turned it on, so far it has been working really well. I chose to replace all the parts I did because of the dryers age, plus I am not familiar with multimeters. Didn't want to risk one old part messing up a new part. Thank you Parts Select.
It is not a 2 hr. repair, but I worked slowly, didn't want to make any mistakes. It would be good if everyone is aware of some of the above information and the YouTube video done by an individual on this particular dryer.
It is not a 2 hr. repair, but I worked slowly, didn't want to make any mistakes. It would be good if everyone is aware of some of the above information and the YouTube video done by an individual on this particular dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!