- Home
- 11096293100
- Instructions
11096293100 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
drier would not heat up
5 of 7 people
found this instruction helpful.
-
PATRICK from PALOS PARK, AL
- Easy
- Less than 15 mins
-
Screw drivers
i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on
Was this helpful?
Thank you for voting!
Unit not spent
4 of 4 people
found this instruction helpful.
-
Boonkham from SMYRNA, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver
Just replaced part
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people
found this instruction helpful.
-
Kevin from VALDOSTA, GA
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
Dryer ran but without heat.
4 of 4 people
found this instruction helpful.
-
barbara from SOUTHAMPTON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the The
... Read more
rmal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!
Read less
Was this helpful?
Thank you for voting!
My idler pully was squealing
4 of 5 people
found this instruction helpful.
-
Anthony from SAINT CLOUD, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it
... Read more
took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Read less
Was this helpful?
Thank you for voting!
Element not heating up.
4 of 5 people
found this instruction helpful.
-
Phillip from Breinigsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistanc
... Read more
e from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !
Read less
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people
found this instruction helpful.
-
Anthony from PITTSTON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered
... Read more
a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't heat.
4 of 5 people
found this instruction helpful.
-
Stan from Boswell, OK
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal F
... Read more
use blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.
Read less
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people
found this instruction helpful.
-
PHILLIP from AUSTIN, MN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use
... Read more
locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Read less
Was this helpful?
Thank you for voting!
Belt was raffling and there was aloud knocking sound
3 of 3 people
found this instruction helpful.
-
Genette from CLEVELAND, MS
- Really Easy
- 15 - 30 mins
-
Socket set
Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it
Was this helpful?
Thank you for voting!
dryer will not,dry clothes,but drum run
4 of 6 people
found this instruction helpful.
-
atolfo from allentown, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text ... Read more in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text ... Read more in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
Read less
Was this helpful?
Thank you for voting!
Dryer was very loud and sounded like it was scraping
3 of 3 people
found this instruction helpful.
-
Annde from JEFFERSON CTY, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people
found this instruction helpful.
-
james from york, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
Squeaky dryer
3 of 3 people
found this instruction helpful.
-
robert from ELMA, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Ezee pezee lemon squeezee.
Was this helpful?
Thank you for voting!
No heat from dryer.
3 of 3 people
found this instruction helpful.
-
Nelson from RAVENSWOOD, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
1.Removed lower dryer cover - two screws. 2.Tested heating element circuit including high temp cutoff, - Heating element circuit was "open" so I first tested the heating element - "open" so I removed one screw on the side and removed the element - element broken. 3.Ordered the part - good price and the deliver was great, three days. 4.
... Read more
Cleaned any lint up and Installed the new heating element and front panel 5. Heated right up - probably saved myself a good $100 for less than thirty minutes of work!!!!
Read less
Was this helpful?
Thank you for voting!