- Home
- 11096293100
- Instructions
11096293100 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people
found this instruction helpful.
-
michael from indianapolis, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl
... Read more
aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.
Thanks Mike
It was a very simple repair.
Thanks Mike
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The dryer suddenly started running cold - it would turn, the timer worked...but no heat. My wife mentioned that it had been taking longer and longer to dry a load of clothes....
12 of 12 people
found this instruction helpful.
-
Geoff from Farmington, CT
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Popped the lower cover off the dryer, found the thermal fuse and thermostat mounted on the heating tube. Removed the screws with a nutdriver, swapped wires to the new parts, and reinstalled. Then I spent 30 minutes vacuuming 13 years worth of lint and crud out of the machine - it was pretty gummed up in spots, which is probably the cause
... Read more
of the failure.
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
I have a 25 foot run of hose from the dryer outside, so I replaced that with 4" metal ducting. Clothes dry much faster now!!! Maybe my electric bill will go down (fat chance :) )
Read less
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people
found this instruction helpful.
-
JEANMARIE from BELLEROSE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people
found this instruction helpful.
-
William from Pontiac, MO
- Easy
- More than 2 hours
-
Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
The Dryer stopped working completely.
13 of 18 people
found this instruction helpful.
-
Elyse from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.
Was this helpful?
Thank you for voting!
dryer would stall and the motor would hum before tripping circuit breaker
11 of 12 people
found this instruction helpful.
-
Charles from Placentia, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wr
... Read more
ench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).
I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.
This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.
The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.
This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.
The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
Read less
Was this helpful?
Thank you for voting!
Dryer produced no heat. My lint trap was full of wet lint.
11 of 12 people
found this instruction helpful.
-
William from LAUREL, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant a ... Read more mount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant a ... Read more mount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
One of the drum support rollers was worn out
13 of 19 people
found this instruction helpful.
-
David from Fleetwood, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not generate heat
11 of 13 people
found this instruction helpful.
-
Douglas from Greensburg, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
My dad was ready to spend $2000 on a new washer/dryer (he has to have a matching set!). Anyway, his dryer would not generate heat. A google search turned up partselect.com, which walked me through the procedure to see what we needed.
It turned out to be a simple to replace $25.00 part! The dryer is drying as if it was brand ... Read more new. Saved $1,975. Hehe.
Thanks, partselect!
It turned out to be a simple to replace $25.00 part! The dryer is drying as if it was brand ... Read more new. Saved $1,975. Hehe.
Thanks, partselect!
Read less
Was this helpful?
Thank you for voting!
my dryer would not heat up any longer
10 of 11 people
found this instruction helpful.
-
Chris from Great Bend, KS
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screw
... Read more
s back in and fastend the front back on and were in bussiness!
Read less
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people
found this instruction helpful.
-
Peter from HUEYTOWN, AL
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people
found this instruction helpful.
-
Eric from West Chester, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
no heat
9 of 9 people
found this instruction helpful.
-
Hal from Edgewater, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid ou
... Read more
t old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
Read less
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people
found this instruction helpful.
-
Michael from ENOLA, PA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Other Parts Used:
Was this helpful?
Thank you for voting!