11094 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Two leaking hoses in my washing machine
29 of 39 people
found this instruction helpful.
-
Marc from Morton Grove, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
Felt piece coming out of filter
27 of 33 people
found this instruction helpful.
-
Sara from Solon, IA
- Really Easy
- Less than 15 mins
Removed old filter and put in new one.
Was this helpful?
Thank you for voting!
Dryer would not heat up.
26 of 30 people
found this instruction helpful.
-
Roger from Bonners Ferry, ID
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the f
... Read more
ront open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Read less
Was this helpful?
Thank you for voting!
Dryer was making a screaching noise while turning
24 of 24 people
found this instruction helpful.
-
jose from FALLBROOK, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Repaired the 4 drum support rollers, 1 idler assembly, 9 tri rings, and 1 washer that came with the kit, however, the multi rib dryer belt that came with the kit did not fit my dryer. After several attempts to troubleshoot the problem, I realized that the belt was too small. I contacted PartSelect customer service and advised that the
... Read more
multi rib dryer belt that came with the kit was too small and I need to purchase a belt (P/N WP8547157) that fits my dryer. Adam was very courteous and helpful and very apologetic for the belt not being the right one. PartSelect refunded my purchase for the Parts Kit and I purchased the correct multi rib dryer belt. I received the new belt expeditiously and was able to finalize the repairs. Thank you PartSelect for your support and cooperation. Recommend: Advise customers that the belt in the kit may not fit the recommended dryer.
Read less
Was this helpful?
Thank you for voting!
noisy drum
29 of 40 people
found this instruction helpful.
-
Jeff from Mesa, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
Water constantly dripped into washer when it was off.
24 of 25 people
found this instruction helpful.
-
MARK from MARION, MA
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat ... Read more er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat ... Read more er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
Read less
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people
found this instruction helpful.
-
joe from cheswick, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
Convert gas dryer to Propane
25 of 30 people
found this instruction helpful.
-
Leonard from Lemitar, NM
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Received conversion kit. Removed front dryer panel,2 screws. Removed burner tube, 2 screws then removed natural gas orfice.
Installed propane orfice and repalced burner tube.
Removed regulater plug and replaced with new plug from kit using 90 degree ratchet screw driver. Approximately 20 minutes. Dryer working great.
Installed propane orfice and repalced burner tube.
Removed regulater plug and replaced with new plug from kit using 90 degree ratchet screw driver. Approximately 20 minutes. Dryer working great.
Was this helpful?
Thank you for voting!
washer wouldnt agitate or spinn but would drain?
22 of 22 people
found this instruction helpful.
-
lester from Belleville, WI
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
So i replaced the above parts pulled gearbox put new oil in all looked good but when i tryed it filled started spinning for a few sec.then quit again?was makeing a clicking sound so i layed on the floor and the drive coupling was spinning so i took the water pump off and it started agitating and spinning. found about a 6 in.thin piece of
... Read more
wire in it, dont know where it came from but installed a new pump and it works like a new one !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The spin gear was striped.
25 of 31 people
found this instruction helpful.
-
Aaron from Lake Mills, WI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Socket set
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
Was this helpful?
Thank you for voting!
Agitator was locked up
24 of 28 people
found this instruction helpful.
-
Roger from Palmyra, IN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two ho
... Read more
ses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger
Read less
Was this helpful?
Thank you for voting!
Noisy Dryer
22 of 22 people
found this instruction helpful.
-
Patrick from SCHENECTADY, NY
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaf
... Read more
t they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.
Read less
Was this helpful?
Thank you for voting!
dryer stoped heating
23 of 26 people
found this instruction helpful.
-
valerie from Elasmore, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this helpful?
Thank you for voting!
Dyer would not heat, flame would shut off within 10 seconds
24 of 29 people
found this instruction helpful.
-
Christy from Riley, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Was this helpful?
Thank you for voting!
Knob broke off
23 of 27 people
found this instruction helpful.
-
Karen from Livonia, MI
- Really Easy
- Less than 15 mins
I was doing my laundry and when I went to turn the knob ot start the next load the knob just broke off in my hand - the machine is 15 years old and I've only needed to do one other small repair so all-in-all I can't complain but what a pain when you're in the middle of doing multiple loads. I found the part on the "official" site but it
... Read more
was costly and we probably wouldn't get it quickly - other option was to pick it up at a store about 2 hours away - with gas prices that wasn't an option.
Found Part Select - found the part - ordered (for about $5 less) - got it a couple of days later - twisted it on the threaded part and the washer was working within 30 seconds.
I would highly recommend Part Select and will use them for all my parts needs.
Found Part Select - found the part - ordered (for about $5 less) - got it a couple of days later - twisted it on the threaded part and the washer was working within 30 seconds.
I would highly recommend Part Select and will use them for all my parts needs.
Read less
Was this helpful?
Thank you for voting!