110888 Kenmore Dryer - Instructions

All Instructions for the 110888
121 - 135 of 357

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would not run because catch did not hold tight enough to press door switch.
1 person found this instruction helpful.
  • j from TAZEWELL, TN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person found this instruction helpful.
  • Barbara from NORTH EASTON, MA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person found this instruction helpful.
  • Kenneth from UPPR MARLBORO, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Susan from HUDSON, MA
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Dryer drum wasn't turning
1 person found this instruction helpful.
  • Carrie from PLAINFIELD, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person found this instruction helpful.
  • Mark from TERREBONNE, OR
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Frank from ENDICOTT, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
Broken door switch
2 of 4 people found this instruction helpful.
  • john from el paso, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Was this helpful?
Thank you for voting!
dryer stopped and smelled of smoke.
2 of 4 people found this instruction helpful.
  • Jon from LaGrange, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people found this instruction helpful.
  • satyavenkata from Bentonville, AR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
Buzzing sound while start button pushed. then shut off after 30 seconds.
2 of 4 people found this instruction helpful.
  • Brad from Lake City, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy
Was this helpful?
Thank you for voting!
Noise in dryer when dryer was turned on
2 of 4 people found this instruction helpful.
  • Michael from Marion, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person found this instruction helpful.
  • Joe from St. Louis, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
Dryer was making all kinds of noises
1 person found this instruction helpful.
  • Noel from N BRANFORD, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and altho ugh not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person found this instruction helpful.
  • Lindsey from Lancaster, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this helpful?
Thank you for voting!
All Instructions for the 110888
121 - 135 of 357