110886 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door latch (female part) was broken.
11 of 11 people
found this instruction helpful.
-
JEANMARIE from BELLEROSE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
The Dryer stopped working completely.
13 of 18 people
found this instruction helpful.
-
Elyse from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.
Was this helpful?
Thank you for voting!
dryer would stall and the motor would hum before tripping circuit breaker
11 of 12 people
found this instruction helpful.
-
Charles from Placentia, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wr
... Read more
ench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).
I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.
This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.
The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.
This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.
The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
Read less
Was this helpful?
Thank you for voting!
Pump but not spin-oil leaking-agitation noise
11 of 12 people
found this instruction helpful.
-
Alvaro from CLEMENTON, NJ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the lo
... Read more
ng shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.
Read less
Was this helpful?
Thank you for voting!
One of the drum support rollers was worn out
13 of 19 people
found this instruction helpful.
-
David from Fleetwood, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was leaking underneath machine
10 of 10 people
found this instruction helpful.
-
RAY from DEER PARK, TX
- Easy
- 30 - 60 mins
While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be
... Read more
necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was leaking.. determined it was center gasket
10 of 10 people
found this instruction helpful.
-
Diane from BALTIMORE, MD
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer tub would not spin or agitate and made a high pitch spinning noise during those cycles.
10 of 10 people
found this instruction helpful.
-
Neil from Winfield, IL
- Very Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
Basically I followed the great instructions provided on the Part Select webpages. I would consider myself to have more common sense than mechanical skill. I didn't want to have to keep going back to purchase more parts so I decided to buy the motor coupler (under $5), new clutch assembly (Under $30), new motor (under $160). The shaft o
... Read more
n the original motor wore down to a cylindrical shape which should have been more of a rectangular shape to fit precisely into the motor coupler and provide the grip strength for the washer tub to spin. Usually the no spin problem is linked to a faulty motor coupler. I was glad that I had to removed the motor to reach the motor coupler because in my case the coupler had not failed. That is when I saw the motor shaft had worn. Since I had all the new parts I replaced them all and since 6/13/19 the washer is running like new. Oh, the problem was most likely caused by someone in my family "overloading" the wash machine one too many times over 11 years. Guy's / Gal's you can do this and save yourself from buying a new washer for between $850 - $1,200. My repair expense was under $240 including tax and next day delivery of my parts. Thanks Part Select !!!! Neil
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Upper agitator did not rotate
11 of 14 people
found this instruction helpful.
-
Robert from Brooksville, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the rinse dispenser from Agitator. Unbolted and removed agitator from machine.
Directions said remove upper agitator by pulling apart. Had to brace bottom with both feet, and lift straight up. Came off. Replaced 4 cogs, re=assembled and re-installed.
Directions said remove upper agitator by pulling apart. Had to brace bottom with both feet, and lift straight up. Came off. Replaced 4 cogs, re=assembled and re-installed.
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people
found this instruction helpful.
-
Eric from West Chester, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Replacement of the water inlet vaqlve
11 of 14 people
found this instruction helpful.
-
William from Chester, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
First I disconnected the inlet hoses. After lifting up the cover the electrical wires were marked and disconnected from the old valve. Next the short hose from the old valve to the tub was removed. Then the old valve was removed from the washing machine by removal of two mounting screws. The new valve was installed in the reverse orde
... Read more
r. New hose clamps were installed on the short hose from the valve to the tub. New washers were installed on the hoses which connected to the valve. A test was made to check for any leaks.
Read less
Was this helpful?
Thank you for voting!
washing machine not draining
10 of 11 people
found this instruction helpful.
-
michael from princeton, TX
- Easy
- 15 - 30 mins
-
Pliers
Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.
Was this helpful?
Thank you for voting!
Not heating
12 of 17 people
found this instruction helpful.
-
Robin from Cedareadge, CO
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
installed according to directions, went well. However I recommend getting a newer dryer, it is 15 years old and didn't work all that well, even when fixed.
Was this helpful?
Thank you for voting!
Crossed threaded plastic on old valve was leaking
11 of 14 people
found this instruction helpful.
-
David from Amity, AR
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of
... Read more
the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.
Read less
Was this helpful?
Thank you for voting!
Replaced ring that broke and washer that was bent on the edge.
22 of 47 people
found this instruction helpful.
-
Kim from West Liberty, OH
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and starte
... Read more
d stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!