1108849 Kenmore Washer Dryer Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The drum made a lot of noise while turning. The dryer shook
3 of 3 people
found this instruction helpful.
-
Craig from VASS, NC
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Other Parts Used:
Was this helpful?
Thank you for voting!
The washing machine was leaking.
3 of 3 people
found this instruction helpful.
-
Matthew from Affton, MO
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I followed the provided video for changing the centerpost gasket.
I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.
If a man is somewhat handy, this is a doable ... Read more repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.
It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.
I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.
If a man is somewhat handy, this is a doable ... Read more repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.
It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.
Read less
Was this helpful?
Thank you for voting!
a broken belt
6 of 12 people
found this instruction helpful.
-
Dorise from Donalsonville, GA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable)
my hany man did it....
Was this helpful?
Thank you for voting!
the lower drum support roller had been chewed to bits.
3 of 4 people
found this instruction helpful.
-
Rodney from Mt. Jackson, VA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with
... Read more
wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
Read less
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people
found this instruction helpful.
-
Mark from Clarksburg, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R
... Read more
einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Read less
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people
found this instruction helpful.
-
WILFRED from NORTH HIGHLANDS, CA
- Really Easy
- Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people
found this instruction helpful.
-
Ed from Charlottesville, VA
- Easy
- Less than 15 mins
-
Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen
... Read more
t, and other parts. At some point it will be time for a new dryer...
Read less
Was this helpful?
Thank you for voting!
when cold water was entering the machine, there were really loud vibrations through the pipes. Sometimes the flow rate was very slow.
3 of 4 people
found this instruction helpful.
-
Glenn from Clearwater, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going
... Read more
to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.
Read less
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people
found this instruction helpful.
-
Russell from Apache Junction, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u
... Read more
p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Read less
Was this helpful?
Thank you for voting!
Lint trap was warped and would not stay in the opening.
3 of 4 people
found this instruction helpful.
-
Carmella from THONOTOSASSA, FL
- Very Easy
- 15 - 30 mins
Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people
found this instruction helpful.
-
Wayne from Rosenberg, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate
... Read more
d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Read less
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people
found this instruction helpful.
-
Cynthia M from Westfield, MA
- Easy
- More than 2 hours
-
Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too
... Read more
shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Read less
Was this helpful?
Thank you for voting!
could not get the bottom agitator to release, so finally just left it in place, first bolt I had did not fit right so ordered one directly from your store also had to wait dor my tools to get in
3 of 4 people
found this instruction helpful.
-
Linda Dianne from Poteau, OK
- A Bit Difficult
- More than 2 hours
-
Socket set
I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place a
... Read more
nd the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story
Read less
Was this helpful?
Thank you for voting!
one of my rollers fell to pieces
2 of 2 people
found this instruction helpful.
-
james from Fredericksburg, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
Was this helpful?
Thank you for voting!