110883 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer stopped and smelled of smoke.
2 of 4 people
found this instruction helpful.
-
Jon from LaGrange, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be
... Read more
removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Read less
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person
found this instruction helpful.
-
Lindsey from Lancaster, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the
... Read more
drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Read less
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person
found this instruction helpful.
-
Steven from New Richmond, WI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You
... Read more
just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Read less
Was this helpful?
Thank you for voting!
Dryer would not heat and the timer would not turn as it should
1 person
found this instruction helpful.
-
Jeff from OAKLAND, TN
- Really Easy
- 30 - 60 mins
-
Socket set
I replaced a bad thermostat
Was this helpful?
Thank you for voting!
Dryer making excessive noise; then continued to blow circuit
1 person
found this instruction helpful.
-
Ava from BALTIMORE, MD
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit
... Read more
-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Read less
Was this helpful?
Thank you for voting!
rollers had been new too long!
1 person
found this instruction helpful.
-
Scott from EVEREST, KS
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person
found this instruction helpful.
-
Joe from St. Louis, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
Loud hum but wouldn't work with a load in
2 of 4 people
found this instruction helpful.
-
Ronald from Tulsa, OK
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.
Was this helpful?
Thank you for voting!
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
1 person
found this instruction helpful.
-
Mark from BLOOMFIELD, CT
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this helpful?
Thank you for voting!
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
door would stay closed
1 person
found this instruction helpful.
-
william from KILLEEN, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person
found this instruction helpful.
-
Melody from TEXARKANA, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
broken belt
1 person
found this instruction helpful.
-
William from Newport, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in busine
... Read more
ss
Read less
Was this helpful?
Thank you for voting!
Seal snapped, which lead to longer dry cycles.
2 of 4 people
found this instruction helpful.
-
Christian from Sunapee, NH
- Really Easy
- Less than 15 mins
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this helpful?
Thank you for voting!