1108799 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would not turn on
3 of 3 people
found this instruction helpful.
-
donald from MANVILLE, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
not drying completely on the automatic settings
3 of 3 people
found this instruction helpful.
-
Jason from Colorado Springs, CO
- Easy
- Less than 15 mins
-
Pliers
Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen.
... Read more
Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.
Read less
Was this helpful?
Thank you for voting!
Clothes were not drying on auto sensor.
3 of 3 people
found this instruction helpful.
-
Michael from Annapolis, MD
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this helpful?
Thank you for voting!
Dryer won't start.Only make a click noise.
3 of 4 people
found this instruction helpful.
-
Candido from GREENVILLE, TX
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people
found this instruction helpful.
-
Wayne from Rosenberg, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate
... Read more
d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Read less
Was this helpful?
Thank you for voting!
Dryer door actuator lever broke
3 of 4 people
found this instruction helpful.
-
Mark from Clarksburg, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R
... Read more
einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Read less
Was this helpful?
Thank you for voting!
door switch lever/latch broke
3 of 4 people
found this instruction helpful.
-
Ed from Charlottesville, VA
- Easy
- Less than 15 mins
-
Screw drivers
You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating elemen
... Read more
t, and other parts. At some point it will be time for a new dryer...
Read less
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people
found this instruction helpful.
-
WILFRED from NORTH HIGHLANDS, CA
- Really Easy
- Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Loud squeaking noise
3 of 4 people
found this instruction helpful.
-
Steven from WICHITA, KS
- Really Easy
- 30 - 60 mins
-
Pliers
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this helpful?
Thank you for voting!
belt was cracking and dryer was somewhat noisy
4 of 7 people
found this instruction helpful.
-
Melody from Silverton, CO
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers
I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, rol
... Read more
ler, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.
Read less
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people
found this instruction helpful.
-
Cynthia M from Westfield, MA
- Easy
- More than 2 hours
-
Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too
... Read more
shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Read less
Was this helpful?
Thank you for voting!
Dryer motor bearings failed. Motor wouldn't start.
8 of 19 people
found this instruction helpful.
-
Mark from Maple Valley, WA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way.
... Read more
The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.
Read less
Was this helpful?
Thank you for voting!
electric dryer stopped heating - the thermostat got very hot
4 of 8 people
found this instruction helpful.
-
Ignas from Midpines, CA
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find whe
... Read more
re they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
Read less
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people
found this instruction helpful.
-
Carl from MARION, KY
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!