1108699 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Roller Berings were worn out - replaced both
4 of 5 people
found this instruction helpful.
-
Gregory from COCOA, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
Dryer wouldn't heat.
4 of 5 people
found this instruction helpful.
-
Stan from Boswell, OK
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal F
... Read more
use blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.
Read less
Was this helpful?
Thank you for voting!
dryer did not run
3 of 3 people
found this instruction helpful.
-
Gerald from STATE COLLEGE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
remove top, front, drum, fan fan housing, replace motor
Was this helpful?
Thank you for voting!
Dryer squealing loudly during operation
3 of 3 people
found this instruction helpful.
-
Joseph from WEST PALM BCH, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Unplug dryer from 220VAC outlet
Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.
Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together ... Read more . You may need a small flat blade screwdriver to seperate connector.
Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.
Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.
Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.
Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.
Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.
At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.
Install new tensioner, tighten slightly, then put springs back on.
Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.
This dryer was quieter than its owners remembered it being back when new 15 years ago.
Well worth saving the $ doing your own work.
Good luck on your repair endeavor!
Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.
Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together ... Read more . You may need a small flat blade screwdriver to seperate connector.
Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.
Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.
Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.
Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.
Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.
At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.
Install new tensioner, tighten slightly, then put springs back on.
Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.
This dryer was quieter than its owners remembered it being back when new 15 years ago.
Well worth saving the $ doing your own work.
Good luck on your repair endeavor!
Read less
Was this helpful?
Thank you for voting!
Dryer would squeal when the drum was turning
3 of 3 people
found this instruction helpful.
-
Clinton from MINOOKA, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace t
... Read more
hem all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Read less
Was this helpful?
Thank you for voting!
Squealing when running
3 of 3 people
found this instruction helpful.
-
MICHAEL from Baden, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.
Was this helpful?
Thank you for voting!
dryer making noise. order parts
4 of 6 people
found this instruction helpful.
-
Thomas from TULELAKE, CA
- Very Difficult
- 30 - 60 mins
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
Read less
Was this helpful?
Thank you for voting!
dryer will not,dry clothes,but drum run
4 of 6 people
found this instruction helpful.
-
atolfo from allentown, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text ... Read more in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text ... Read more in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve
Read less
Was this helpful?
Thank you for voting!
A hole in filter
3 of 3 people
found this instruction helpful.
-
Russ from Vernal, UT
- Really Easy
- Less than 15 mins
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this helpful?
Thank you for voting!
dryer would not turn on
3 of 3 people
found this instruction helpful.
-
donald from MANVILLE, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
Washer wouldn’t drain and spin
3 of 3 people
found this instruction helpful.
-
Thomas from KENT, CT
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re ... Read more moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re ... Read more moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Read less
Was this helpful?
Thank you for voting!
Dryer would shut off mid way through cycle and give an E1 error code
5 of 9 people
found this instruction helpful.
-
Dwayne from Bainbridge, PA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back
... Read more
together in reverse. I also took the time to clean any dust and lint out.
Read less
Was this helpful?
Thank you for voting!
Start and then kick out.
5 of 9 people
found this instruction helpful.
-
PHILLIP from AUSTIN, MN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use
... Read more
locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.
Read less
Was this helpful?
Thank you for voting!
Dryer would not run
4 of 6 people
found this instruction helpful.
-
james from york, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
Was this helpful?
Thank you for voting!
Dryer was very loud and sounded like it was scraping
3 of 3 people
found this instruction helpful.
-
Annde from JEFFERSON CTY, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Was this helpful?
Thank you for voting!