1108698 Kenmore Dryer - Instructions

All Instructions for the 1108698
121 - 135 of 1822

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the drum support rollers was worn out
13 of 19 people found this instruction helpful.
  • David from Fleetwood, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Was this helpful?
Thank you for voting!
Dryer stopped spinning
13 of 19 people found this instruction helpful.
  • Danielle from FREEDOM, IN
  • Really Easy
  • More than 2 hours
  • Nutdriver, Screw drivers
The dryer quit working. I did some trouble shooting on your amazing site, ordered what i thought it might need and then got to work. Took no time to get it apart and replace roller kit and belt. What took the longest was getting in there and cleaning out probably 15 years worth of dirt and dust. If you have not opened your dryer up and d one this, 10/10 recommend, because in doing so i found that the motor was the real culprit. Once i opened it up more, especially cleaning around the blower fan and motor, i was half a day in. Put it all back together and got it running for two more loads before the motor quit. Replaced that and since the hard work was done, had it back in in half an hour and running great. Probably will need to redo the felt seal one day, but for now, i am calling it a win. This is my go to site for all things and i have been able to work on most of my major appliances and do it myself using the helpful information here.
Was this helpful?
Thank you for voting!
my dryer would not heat up any longer
10 of 11 people found this instruction helpful.
  • Chris from Great Bend, KS
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screw s back in and fastend the front back on and were in bussiness!
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people found this instruction helpful.
  • Eric from West Chester, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people found this instruction helpful.
  • Peter from HUEYTOWN, AL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Badly worn idler pulley and rollers.
11 of 14 people found this instruction helpful.
  • TODD from GRASS VALLEY, CA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Braced dryer drum with a block. Removed the two rollers one at a time by using a screwdriver to pop off the triangular clip. Slid on new rollers. Would have been easier to remove the drum out the front instead of bracing it. Installed new idler pulley and belt. Dryer is 25 years old and sounds like a new one now when running.
Was this helpful?
Thank you for voting!
replace lint filter
10 of 11 people found this instruction helpful.
  • Ed from Greensboro, NC
  • Really Easy
  • Less than 15 mins
with both hands
Was this helpful?
Thank you for voting!
broken clip on top panel hold down
15 of 26 people found this instruction helpful.
  • Mark from Huntington Station, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
no heat
9 of 9 people found this instruction helpful.
  • Hal from Edgewater, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid ou t old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
Was this helpful?
Thank you for voting!
Replaced a broken pulley.
10 of 12 people found this instruction helpful.
  • Brian from IMLAY CITY, MI
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Wrench set
Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Dryer runs heats up, will run for a short period and then shuts down, after a minute or two it will come back on and will resume drying.
18 of 36 people found this instruction helpful.
  • John from Brookings,, OR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.
Was this helpful?
Thank you for voting!
Wouldn't heat
10 of 12 people found this instruction helpful.
  • Lorraine from Elk Grove, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
My husband said it was very easy and quick. We will recomend your site for sure.
Was this helpful?
Thank you for voting!
All Instructions for the 1108698
121 - 135 of 1822