1108698 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat When Drying
60 of 70 people
found this instruction helpful.
-
DAVID from CHARLOTTE, NC
- Easy
- 30 - 60 mins
-
Nutdriver
I followed the tips from the repair video. Easy as 1-2-3. I changed both the heating element as well as the thermal cut off. Went ahead and repaired the door catch. Brand new dryer for the next 10 years. I do advise to pull out your shop vac and remove the tons of lint that accumulates in the bottom. A definite fire hazardous. I
... Read more
do attest that this web site is the best by far.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people
found this instruction helpful.
-
RONALD from SALMON, ID
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!
Our dryer started squealing and would then stop running.
55 of 69 people
found this instruction helpful.
-
Kelly from Aptos, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The par ... Read more t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The par ... Read more t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
Read less
Was this helpful?
Thank you for voting!
the dryer only blew cold air
48 of 52 people
found this instruction helpful.
-
charles from waukesha, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
Was this helpful?
Thank you for voting!
Dryer quit heating.
46 of 53 people
found this instruction helpful.
-
Jo from BANDON, OR
- Easy
- More than 2 hours
-
Pliers, Screw drivers, Socket set
This dryer is 30 plus years old. I am a 71 year old female that has never taken on this type of repair. First I very carefully ordered all parts possibly associated with this problem. Watched all videos available for this model. Could not find one at Parts Select that addressed this particular dryer. Model number was correct. Finally
... Read more
found YouTube video that addressed an "Old Kenmore Wood Top". It showed the correct way to remove the Heating Element unit. Also Parts Select never mentions that fuses and sensors are not "polarized". Very important info for a novice. But Google helped me with that. Heating Element is "polarized", very important not to cross wires. I did order a couple Heating Element Connection Wire Kits that were not needed for this repair. Got all parts replaced, put dryer back together, crossed my fingers and turned it on, so far it has been working really well. I chose to replace all the parts I did because of the dryers age, plus I am not familiar with multimeters. Didn't want to risk one old part messing up a new part. Thank you Parts Select.
It is not a 2 hr. repair, but I worked slowly, didn't want to make any mistakes. It would be good if everyone is aware of some of the above information and the YouTube video done by an individual on this particular dryer.
It is not a 2 hr. repair, but I worked slowly, didn't want to make any mistakes. It would be good if everyone is aware of some of the above information and the YouTube video done by an individual on this particular dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer motor would not turn on
51 of 69 people
found this instruction helpful.
-
John from Bluffton, SC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench set
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to
... Read more
pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
Read less
Was this helpful?
Thank you for voting!
Drum of the dryer was rotating but no heating
45 of 52 people
found this instruction helpful.
-
Tomasz from University Heights, OH
- Really Easy
- Less than 15 mins
-
Socket set
First I removed the back cover (several screws). Then, I disconected wires from the high-limit thermostat and the thermal cut-off fuse (both of these parts were included in the Thermal Cut-Off Kit). Then, I removed four screws that hold these two parts, replaced the parts, put the screws back, and attached the wires. Finally, I put back t
... Read more
he cover.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't turn on
49 of 64 people
found this instruction helpful.
-
Olive from Williamsburg, OH
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
Read less
Was this helpful?
Thank you for voting!
TOb stopped turning after a week or so of high pitched "squeals" coming from inside the dryer.
43 of 48 people
found this instruction helpful.
-
Robert from Princeton, WV
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as
... Read more
the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.
Read less
Was this helpful?
Thank you for voting!
No power
45 of 55 people
found this instruction helpful.
-
Nick from Brandon, FL
- Easy
- 1- 2 hours
-
Nutdriver
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total
... Read more
price of $35, figured I saved at least $150 on a service call by Whirpool.
Read less
Was this helpful?
Thank you for voting!
Busted Belt & Pulley
43 of 51 people
found this instruction helpful.
-
James from West Haven, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I bought a belt from a store in my area- What a mistake...I found this site and read all the stories on how easy it was and how PartSelect.com had the parts in stock and had easy instructions...I put the idler pulley in place, put the belt in place (all from instructions included) and put the dryer back together (which was easy). I actua
... Read more
lly did it alone. I would recommend this company to anyone in need of their parts and help!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not heat at all.
42 of 48 people
found this instruction helpful.
-
Lou from Orlando, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Found a service manual on-line for the Whirlpool Duet Dryer. Did the troubleshooting for the problem stated. Found the heater element to be bad (open circuit across heater block). Ordered new element from PartSelect.com and installed. Dryer now works like a charm and I didn't have to call a repairman.
Was this helpful?
Thank you for voting!
Dryer would not shut off on auto dry settings
42 of 50 people
found this instruction helpful.
-
Wiliam from Belleville, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.
Was this helpful?
Thank you for voting!
worn out part
44 of 64 people
found this instruction helpful.
-
John from Tucson, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Other Parts Used:
Was this helpful?
Thank you for voting!
Needed lint filter for my old Kenmore dryer that was no longer manufactured by Sears.
35 of 37 people
found this instruction helpful.
-
Richard from Fairfax, VA
- Really Easy
- Less than 15 mins
Lint filter supplied by Parts Select was an exact replacement by an aftermarket manufacturer. I put the old one and the new one side by side and they were identical (of course, the handle wasn't broken off on the new one!). I coulnd't be happier. It arrived at my house 2 days after I ordered it. I highly recommend Parts Select.
Was this helpful?
Thank you for voting!