1108656 Kenmore Dryer - Instructions

All Instructions for the 1108656
31 - 45 of 1567

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer motor would not turn on
51 of 69 people found this instruction helpful.
  • John from Bluffton, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
Was this helpful?
Thank you for voting!
Dryer wouldn't turn on
49 of 64 people found this instruction helpful.
  • Olive from Williamsburg, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience fo r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
Was this helpful?
Thank you for voting!
TOb stopped turning after a week or so of high pitched "squeals" coming from inside the dryer.
43 of 48 people found this instruction helpful.
  • Robert from Princeton, WV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.
Was this helpful?
Thank you for voting!
No power
45 of 55 people found this instruction helpful.
  • Nick from Brandon, FL
  • Easy
  • 1- 2 hours
  • Nutdriver
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.
Was this helpful?
Thank you for voting!
Busted Belt & Pulley
43 of 51 people found this instruction helpful.
  • James from West Haven, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I bought a belt from a store in my area- What a mistake...I found this site and read all the stories on how easy it was and how PartSelect.com had the parts in stock and had easy instructions...I put the idler pulley in place, put the belt in place (all from instructions included) and put the dryer back together (which was easy). I actua lly did it alone. I would recommend this company to anyone in need of their parts and help!
Was this helpful?
Thank you for voting!
Dryer would stop running after several minutes. Once cooled it would start again. Motor worn out and binding.
41 of 54 people found this instruction helpful.
  • Angela from Houston, TX
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Remove back cover
Raise top
Remove filter assembly
Remove front cover and drum

Tip: Use an end wrench on the fan and another on the pully shaft of the motor to remove fan from motor prior to removing motor from cradle.

Vacuum everything while disassembled

Remember to take your time and not f orce anything and this will go smooth.
Was this helpful?
Thank you for voting!
Needed lint filter for my old Kenmore dryer that was no longer manufactured by Sears.
35 of 37 people found this instruction helpful.
  • Richard from Fairfax, VA
  • Really Easy
  • Less than 15 mins
Lint filter supplied by Parts Select was an exact replacement by an aftermarket manufacturer. I put the old one and the new one side by side and they were identical (of course, the handle wasn't broken off on the new one!). I coulnd't be happier. It arrived at my house 2 days after I ordered it. I highly recommend Parts Select.
Was this helpful?
Thank you for voting!
worn out part
44 of 64 people found this instruction helpful.
  • John from Tucson, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.
Was this helpful?
Thank you for voting!
dryer drum wouldn't turn
36 of 40 people found this instruction helpful.
  • Steve from Peachtree City, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure ou t you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!
Was this helpful?
Thank you for voting!
Dryer door cable broken
37 of 46 people found this instruction helpful.
  • George from Rochester Hills, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1. Remove the lint filter. Then remove 2 screws at the lint filter housing.

2. At the back of the dryer, remove 2 screws that restrain the hinges for the dryer top. Do NOT remove the hinges.

3. Remove the front lower access panel. It snaps at the top and hinges at the bottom. It can be slipped off the hinges. ... Read more />
4. Remove 2 screws at the bottom of the main front panel

5. The front of the dryer top is held in place by two plastic clips. Use a flat blade screwdriver (with a rag wrapped around the tip to minimize paint damage) to pry the top up at each front corner. Then tilt the top up to just past vertical. You now can see the top of the spring that is connected to the door cable.

6. Open the dryer door. Use a putty knife to pry up the plastic plug that holds the cable in place at the door. Remove the old cable from the door and insert the new one. Be sure the cable end without a hole goes into the dryer door. Replace the plastic plug.

7. Feed the new cable through the main front panel and close the door.

8. Loosen but do NOT remove two screws that hold the main front panel to each side panel. Tilt the bottom of the front panel out about 2 inches.

9. Working through the gap between the main front panel and the side, hook the spring into the hole in the cable end.

10. Working through the open top and the gap on the side, move the spring+cable up to the top. Pass the upper end of the spring through the rectangular hole in the top of the main front panel and hook the end into the small hole there.

11. Repeat for other cable as needed.

12. Reassemble all parts. You may need to hold the top of the drum up as you move the main front panel back into place. Install the main front panel lower screws before tightening the upper screws.
Was this helpful?
Thank you for voting!
The dryer was leaving rust marks on our clothes.
37 of 48 people found this instruction helpful.
  • Lauren from Mckinney, TX
  • Easy
  • 30 - 60 mins
  • Socket set
After my husband disassembled the cabinet and removed the drum, we used a putty knife to remove the old seal and carefully glued the new one in place. (A 2 man job to do it without leaking glue everywhere.) We then replaced the belt, following the picture sent by PartSelect and put everything back. (We put all small pieces in labeled enve lopes so that putting it back together was easy.) Another helpful hint - take a few digital pictures beforehand in the event that you need to see it to put it back together!
Was this helpful?
Thank you for voting!
Loads in the dryer took a very long time to dry often needing two full cycles to completely dry.
39 of 55 people found this instruction helpful.
  • Rod from Galveston, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First, I moved the dryer out where it would be easily accessable. I then removed the back of the dryer using a nut driver. Once this was complete, I removed the cover holding the heating element. I disconnected the two wires and puled the old element out. I replaced it with the new heating element and reconnected the two wires. I then rep lace the back cover and moved the dryer back in place. The dryer works and heats much better now. Thankyou
Was this helpful?
Thank you for voting!
Drum stopped turning, fan continued to blow
31 of 34 people found this instruction helpful.
  • Richard from Davie, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, e tc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.
Was this helpful?
Thank you for voting!
Dryer belt snapped
33 of 42 people found this instruction helpful.
  • J. from Oakdale, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people found this instruction helpful.
  • Bill from Houston, TX
  • Really Easy
  • Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
All Instructions for the 1108656
31 - 45 of 1567