110862 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer made a terrible squealing noise
7 of 9 people
found this instruction helpful.
-
Will from Charlotte, NC
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.
Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Read less
Was this helpful?
Thank you for voting!
Dryer making squealing noise.
8 of 12 people
found this instruction helpful.
-
Harriet from Palm Coast, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up.
... Read more
Replaced front and top.
Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer wouldn't run
6 of 6 people
found this instruction helpful.
-
Edward from Richlands, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
Extremely easy repair! Unplug the dryer. Remove the lint trap screen. Take the two screws out of the lint trap chute, pry up the top of the dryer, insert wood or have someone hold top up, remove two screws holding the switch in place while holding the switch so the old spring doesn't fall. Remove old spring and replace with new one.
... Read more
Re-attach switch to dryer with two screws. Plug in and test run. Lower top and push firmly to engages clips. Re-install two scres in lint trap chute followed by the lint trap screen and you are finished!
Repair took about five minutes and saved approximately $70!
Repair took about five minutes and saved approximately $70!
Read less
Was this helpful?
Thank you for voting!
Loud screeching noise when dryer running
6 of 6 people
found this instruction helpful.
-
Stephen from Charlotte, NC
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First, removed the bottom cover below the dryer door. This is just held on with two clips that can be pushed in with a flat screw driver. Then remove the springs that go from the bottom of the dryer to the inside of the dryer door. We had to remove the entire front of the dryer, so the easiest way we found was to loosen the two screws
... Read more
on the bottom of the front panel, but not remove them. Then pop up the top of the dryer. To lift the top, first remove the two screws under the little door where the lint trap goes. The top is hinged in the back, and it snaps down onto two clips that can easily be popped up with a flat screw driver) With the top opened, there are two screws accessible. When the front of the dryer is removed, there will be nothing to support the drum, so what we found was that if you rotate the drum, you'll find a point where there's a hole in the top of the drum. If you take the springs that you removed from the bottom of the door you can hook them into this hole, and hook the other end into a hole in the back wall of the dryer just behind the drum. The springs are the perfect size for this, and it keeps the drum from falling when you remove the front panel. then just disconnect the three wires going to the switch inside the front panel, and remove the two screws from the top of the front panel. It should then lift right off. The bearing can just be pulled away and the new one installed. Put everything together again in reverse order.
Read less
Was this helpful?
Thank you for voting!
Dryer stopped spinning.
8 of 12 people
found this instruction helpful.
-
sherif from BARTONSVILLE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Followed the PartSelect instruction video.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.
Basically opened the dryer.
Took the drum out.
Took the broken motor out.
cleanned the dryer since I had everything opened.
Replaced motor, pulley, old belt.
My 20 years old dryer is running like brand new.
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer runs but, no heat
6 of 6 people
found this instruction helpful.
-
Richard from WAVERLY, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
found a video online and followed the instructions. First unplug dryer, then take off back cover with a 1/4 inch socket unscrew the 5 screws from the cover and remove back. Then with a ohms meter you have to check to see what terminals are bad. In my case it was the heating element. So, next you go to top of dryer and unscrew the lint tra
... Read more
p so you can lift the top of dryer and remove the bracket holding the housing where the element is located. First take off the leads that are connected to the element and housing unit. Then gently lift housing unit up off the hinges and pull it out. Then turn over and there is another screw that holds the heating element in. After unscrewed the element pulls right out and then just put new element in and reverse everything.
Read less
Was this helpful?
Thank you for voting!
The dryer start but it did not stay on.
7 of 10 people
found this instruction helpful.
-
Luis from VALDOSTA, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
I replaced the push start buttom,but it still had the same problem,so I went to the motor and found the burnt wire and bingo,we are happy again thanks to your website.
Was this helpful?
Thank you for voting!
Auto Dry Sensor Failed
9 of 16 people
found this instruction helpful.
-
J from Trabuco Canyon, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.
Was this helpful?
Thank you for voting!
Start windings burnt out on original motor (dryer would not start)
7 of 10 people
found this instruction helpful.
-
Frank from Smyrna, TN
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to un
... Read more
thread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
Read less
Was this helpful?
Thank you for voting!
Broken Motor Pulley
7 of 10 people
found this instruction helpful.
-
Mark from PELHAM, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge woul
... Read more
d be thru the roof.
Read less
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people
found this instruction helpful.
-
Betty from Erie, PA
- Really Easy
- 15 - 30 mins
-
Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
Dryer Top Panel is Loose
5 of 5 people
found this instruction helpful.
-
MONTE from CHESAPEAKE, VA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each ... Read more locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each ... Read more locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
Read less
Was this helpful?
Thank you for voting!
Door Gasket Came Off The Dryer And Tangled In Clothes
14 of 32 people
found this instruction helpful.
-
Jennifer from Biloxi, MS
- A Bit Difficult
- 15 - 30 mins
I haven't been able to do the repair yet because the door gasket has to be "glued" in and the gasket doesn't come with a sealer of any sort. It is just the rubber ring. I am going to have to go to my local lowe's or home depot and ask someone to help me find what I need to glue the gasket in place. The repair itself should be simple
... Read more
. The gasket just sits in the "groove," but without a sealer of some sort, the gasket will come loose again and I will be back to having a dryer that takes twice as long to dry my clothes.
Read less
Was this helpful?
Thank you for voting!
Dryer would not activate unless jarred by striking with the hand.
6 of 8 people
found this instruction helpful.
-
DAVID from AKRON, OH
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Investigated inside control panel for loose wires or parts. Removed back of control panel and back of dryer and used a vacuum to remove lint from every possible contact. Problem not fixed.
Lifted top of dryer and cleaned inside. Struck door close switch with a screw driver and dryer started every time. Replaced switch.
... Read more />
Works every time. This is the 3rd repair in over 20 years. Each time the dryer works as though new.
Lifted top of dryer and cleaned inside. Struck door close switch with a screw driver and dryer started every time. Replaced switch.
... Read more />
Works every time. This is the 3rd repair in over 20 years. Each time the dryer works as though new.
Read less
Was this helpful?
Thank you for voting!
Motor was bad
5 of 5 people
found this instruction helpful.
-
Michael from CLIFTON HTS, PA
- Really Easy
- 30 - 60 mins
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part s
... Read more
o I can redo a testimonial here for you. 19 days and still waiting
Read less
Was this helpful?
Thank you for voting!