110847 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
spin cycle was not working / poor
11 of 14 people
found this instruction helpful.
-
Craig from Plano, TX
- Easy
- 30 - 60 mins
-
Pliers, Socket set
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive ass
... Read more
embly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.
Read less
Was this helpful?
Thank you for voting!
Top of washer wasn't attached to base
10 of 11 people
found this instruction helpful.
-
Janel from Las Vegas, NV
- Easy
- 30 - 60 mins
-
Screw drivers
First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the
... Read more
part they broke!
So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.
Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.
Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.
Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.
Easy, right?
So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.
Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.
Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.
Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.
Easy, right?
Read less
Was this helpful?
Thank you for voting!
dryer kept running when door was open
11 of 15 people
found this instruction helpful.
-
Dean from New Bern, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
changed out the switch. easy. about 20 minutes. part came quickly (2-3 days). great service. thanks.
Was this helpful?
Thank you for voting!
Washer would not spin a full load.
11 of 15 people
found this instruction helpful.
-
Ralph from Newbury Park, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.
Was this helpful?
Thank you for voting!
Dryer runs heats up, will run for a short period and then shuts down, after a minute or two it will come back on and will resume drying.
18 of 36 people
found this instruction helpful.
-
John from Brookings,, OR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.
Was this helpful?
Thank you for voting!
Belt broke & renter tried to fix without my knowledge
9 of 9 people
found this instruction helpful.
-
ALLAN W from CYRUS, MN
- Easy
- 30 - 60 mins
-
Nutdriver
When the belt broke my renter tried to fix it with duct tape and in the process the idler pulley either broke or somehow got lost. When I began to fix the dryer with a new belt,I discovered the idler was gone. SO, not knowing what it looked like was a problem. Going to the PartSelect web site I was able to see the exploded views of the
... Read more
whole dryer and pick out the right repair items. Really worked slick. Thanks. Allan W. Rutter
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Rust marks on clothing
13 of 21 people
found this instruction helpful.
-
Patrick from Manor, TX
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Our dryer was leaving rust marks on our clothes that looked like a brown pencil mark. It turns out that the rear drum seal in our dryer was absorbing gunk over the years and we had to change it. It was a fairly easy fix but did require pulling the dryer almost completely apart. While we had it apart we changed this as well.
Any ... Read more one with a socket stet and screw driver can get it all apart.
On our machine, start by removing the 2 screws that hold the lint filter neck to the top of the machine (under the flap).
Then pry the top of the machine up in the front. It will pop up and you can fold it back.
Then you will need to remove 2 bolts and undo the plug.
From there you can pull the front off and get to the drum.Make sure you note how the belt tensioner comes out (under the drum) and how the belt is routed. It's quite basic.
After you get the drum off, peel the old seal(s) off and put the new seal(s) on as directed.
Pretty easy and our clean clothes stay clean now.
Any ... Read more one with a socket stet and screw driver can get it all apart.
On our machine, start by removing the 2 screws that hold the lint filter neck to the top of the machine (under the flap).
Then pry the top of the machine up in the front. It will pop up and you can fold it back.
Then you will need to remove 2 bolts and undo the plug.
From there you can pull the front off and get to the drum.Make sure you note how the belt tensioner comes out (under the drum) and how the belt is routed. It's quite basic.
After you get the drum off, peel the old seal(s) off and put the new seal(s) on as directed.
Pretty easy and our clean clothes stay clean now.
Read less
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people
found this instruction helpful.
-
Dawn from Chesapeake City, MD
- Really Easy
- Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Tub banged against the front of case during spin
9 of 9 people
found this instruction helpful.
-
Peter from Boca Raton, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the
... Read more
suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Read less
Was this helpful?
Thank you for voting!
Washing machine shakes violently during spin cycle
25 of 58 people
found this instruction helpful.
-
James from Asheville, NC
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justa
... Read more
nswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor...
Read less
Was this helpful?
Thank you for voting!
Washer tub off balance and noisy
9 of 10 people
found this instruction helpful.
-
Gregory from Kent, OH
- A Bit Difficult
- 30 - 60 mins
-
Pliers
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag ... Read more e with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag ... Read more e with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Read less
Was this helpful?
Thank you for voting!
Spin cycle not working properly; Clothes still soaked when spin cycle finished
12 of 19 people
found this instruction helpful.
-
Sarah from Columbus, OH
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing complet
... Read more
ely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Machine agitated during cycle but would not spin clothes dry.
10 of 13 people
found this instruction helpful.
-
Kurt from Bremerton, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.
Was this helpful?
Thank you for voting!
Severe wobble during spin cycle.
9 of 11 people
found this instruction helpful.
-
Steven from Dallas, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spr
... Read more
ing bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer basket off-center and wobbling during spin cycle
8 of 8 people
found this instruction helpful.
-
Craig from Woodland Hills, UT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this helpful?
Thank you for voting!