110844 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Spin cycle not working properly; Clothes still soaked when spin cycle finished
12 of 19 people
found this instruction helpful.
-
Sarah from Columbus, OH
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing complet
... Read more
ely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Machine agitated during cycle but would not spin clothes dry.
10 of 13 people
found this instruction helpful.
-
Kurt from Bremerton, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.
Was this helpful?
Thank you for voting!
original Timer knob was made with plastic threads which broke.
9 of 10 people
found this instruction helpful.
-
Rodney from Irving, TX
- Really Easy
- Less than 15 mins
I simply unscrewed the little piece of the original (plastic) left on the metal bolt from the timer knob which broke off and screwed on the new timer knob which was lined with metal instead of plastic. I'm sure this part will outlast my washer which is around 15 years old
Was this helpful?
Thank you for voting!
Leaking water from bottom after wash
9 of 11 people
found this instruction helpful.
-
Robert from Wildomar, CA
- Easy
- 30 - 60 mins
Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished
Other Parts Used:
Was this helpful?
Thank you for voting!
washer would not spin clothes
8 of 8 people
found this instruction helpful.
-
Joseph from KEARNY, NJ
- Really Easy
- 1- 2 hours
-
Socket set
Followed the video instructions. Had no problems. The video was accurate.
Other Parts Used:
Was this helpful?
Thank you for voting!
there was a hole in the original drain hose
10 of 14 people
found this instruction helpful.
-
Kathy from Pittsburgh, PA
- Really Easy
- Less than 15 mins
-
Pliers
First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new ho
... Read more
se onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!
Read less
Was this helpful?
Thank you for voting!
No heat in dryer
10 of 14 people
found this instruction helpful.
-
Noah from Maiden, NC
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Took off the lower front panel, removed duct piece from filter to blower fan, removed two screws and two wires to thermostat in exhaust ducting, then replaced thermostat with new one. Very easy job and everything worked like new when I reassembled it.
Was this helpful?
Thank you for voting!
Direct drive pump was leaking
8 of 8 people
found this instruction helpful.
-
Philip from DENTON, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the
... Read more
hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Washer would'nt spin
9 of 12 people
found this instruction helpful.
-
Dean from Poplar Grove, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
Was this helpful?
Thank you for voting!
Loud rumble noise while drum was turning
9 of 12 people
found this instruction helpful.
-
Marcia from CAmden, NY
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the
... Read more
drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.
Read less
Was this helpful?
Thank you for voting!
Spider coupling between motor and transmission broken
9 of 12 people
found this instruction helpful.
-
Robert from Friendswood, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep
... Read more
air.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
noisy
8 of 9 people
found this instruction helpful.
-
clinton from selah, WA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
just like video showed really helpfull
Was this helpful?
Thank you for voting!
lint filter an cover was stolen by tenant
8 of 9 people
found this instruction helpful.
-
Michael from WEST WARWICK, RI
- Really Easy
- Less than 15 mins
easy three prong push-in,...
Was this helpful?
Thank you for voting!
No agitation, No spin, pump OK
7 of 7 people
found this instruction helpful.
-
Ernest from Midlothian, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold
... Read more
the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water Pump was leaking
9 of 13 people
found this instruction helpful.
-
Rick from Liberty, SC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
I turned the washer on its side and felt where the leak was on th ... Read more e pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.
I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!