- Home
- 11082680310
- Instructions
11082680310 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Direct drive pump was leaking
8 of 8 people
found this instruction helpful.
-
Philip from DENTON, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the
... Read more
hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
With full load, clothes were not agitating correctly - very little action or movement of the upper agitator section.
8 of 8 people
found this instruction helpful.
-
Douglas from Lancaster, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Took off softener dispenser, pried off top of agitator, removed bolt from top of agitator.
Then pulled out the agitator assembly for easier access.
Used screwdriver to brake small plastic keepers holding secondary agitator ratchet clutch to the secondary agitator.
Assembled and inserted new ratchet mechan ... Read more ism in the top of the agitator, making sure 4 small square pegs protruding from the end of the new assembly fully entered into mating holes on the secondary agitator.
Placed the agitator back on the agitator post and installed and secured bolt. Replaced cap and installed softener dispenser.
Then pulled out the agitator assembly for easier access.
Used screwdriver to brake small plastic keepers holding secondary agitator ratchet clutch to the secondary agitator.
Assembled and inserted new ratchet mechan ... Read more ism in the top of the agitator, making sure 4 small square pegs protruding from the end of the new assembly fully entered into mating holes on the secondary agitator.
Placed the agitator back on the agitator post and installed and secured bolt. Replaced cap and installed softener dispenser.
Read less
Was this helpful?
Thank you for voting!
Severe wobble during spin cycle.
9 of 11 people
found this instruction helpful.
-
Steven from Dallas, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spr
... Read more
ing bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer basket off-center and wobbling during spin cycle
8 of 8 people
found this instruction helpful.
-
Craig from Woodland Hills, UT
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this helpful?
Thank you for voting!
Top section of the agitator would not work properly
12 of 20 people
found this instruction helpful.
-
James from Crownsville, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the top cap, unbolted the agitator, lifted off the top section, removed old "dogs" and replaced new "dogs", reinstalled agitator and tested.
Was this helpful?
Thank you for voting!
banging noise during spin cycle, tub out of balance
8 of 9 people
found this instruction helpful.
-
Russell from CHARLTON CITY, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Spider coupling between motor and transmission broken
9 of 12 people
found this instruction helpful.
-
Robert from Friendswood, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy rep
... Read more
air.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
noisy
8 of 9 people
found this instruction helpful.
-
clinton from selah, WA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
just like video showed really helpfull
Was this helpful?
Thank you for voting!
Washer would'nt spin
9 of 12 people
found this instruction helpful.
-
Dean from Poplar Grove, IL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.
Was this helpful?
Thank you for voting!
Electrical burning smell washer stoped working
11 of 19 people
found this instruction helpful.
-
Arthur from Statesville, NC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced motor starting capacitor. Noticed water leak at pump and replaced pump
Other Parts Used:
Was this helpful?
Thank you for voting!
No parts
7 of 7 people
found this instruction helpful.
-
Jason from WENTZVILLE, MO
- Very Difficult
- More than 2 hours
A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Contacted company for a refund and a Retha’s never been issued.
Terrible service!
Other Parts Used:
Was this helpful?
Thank you for voting!
No agitation, No spin, pump OK
7 of 7 people
found this instruction helpful.
-
Ernest from Midlothian, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold
... Read more
the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Washer would not work in agitate or spin cycle
6 of 6 people
found this instruction helpful.
-
yesenia from apopka, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off wit
... Read more
hout unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.
It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.
Read less
Was this helpful?
Thank you for voting!
washer wouldn't spin with load, then not at all with rapid clicking sound
6 of 6 people
found this instruction helpful.
-
Lou from ATLANTIC HLDS, NJ
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems
Other Parts Used:
Was this helpful?
Thank you for voting!