- Home
- 11082467340
- Instructions
11082467340 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water was leaking out to floor after each load
6 of 8 people
found this instruction helpful.
-
James from MILWAUKEE, WI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Replaced the springs after watching the video's from this site and problem has been solved.
Other Parts Used:
Was this helpful?
Thank you for voting!
Cracked drain tube.
6 of 8 people
found this instruction helpful.
-
Eric from Grand Haven, MI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Removed old tube and replaced with new version. Replacement slightly different than original since the new part included a feature that appears to prevent the problem. New part still fit and is operating well so far.
Was this helpful?
Thank you for voting!
tub would not spin....burning smell
6 of 8 people
found this instruction helpful.
-
John from Elm Mott, AL
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Unplugged washer. Pulled the washer away from the wall & leaned it back against the wall to access the underneath side of the washer. Disconnected water hoses to the pump with water pump pliers. Have drain pan handy to catch the water, approximately 1 qt. Remember which hose goes to the proper place. Removed two retaining screws/st
... Read more
raps allowing the motor to be seperated from the transmission. There is enough slack in the wiring to allow you to drop the motor without disconnecting. You do not need to remove the water pump. Removed old coupling & replaced with the new one. Make sure you use the "new style" replacement coupler or you will be doing this repair again very soon! Schematics are available online.
Read less
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people
found this instruction helpful.
-
Matthew from Wauwatosa, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
Loud Screeching noise when draining water
5 of 5 people
found this instruction helpful.
-
Steven from Port Saint Lucie, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to
... Read more
wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Washer would not fill with water...
5 of 5 people
found this instruction helpful.
-
Eddie from Charlotte, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Watched the video on the website... and did what it said to do. It was VERY helpful... It did not fix the problem... so now I'm on to the next possible solution. Also, provided by the website. The valve was the problem 85% of the time. The water level switch is the problem 10% of the time. The water level switch is what I ordered nex
... Read more
t.
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell
Read less
Was this helpful?
Thank you for voting!
Replacing water inlet valve with new one
5 of 5 people
found this instruction helpful.
-
David from HENRY, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her
... Read more
)
Read less
Was this helpful?
Thank you for voting!
slow or no spin
6 of 9 people
found this instruction helpful.
-
Steven from Wausau, WI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
First read up on what others did and tried to find free repair manual with little luck. Called repairman, they thought whole transmission was shot- would have been $70 just to have them look- forget it. Getting it apart: popped off the two console cosmetic panels to get to a screw on each side from the top. Lifted off console, levered
... Read more
and squeezed retaining clips. Unhooked two connectors and overflow tubing? Shell pulled off easily, getting back on after I was all done made me wonder if it was a good choice. In the end yes- allowed me to clean inside surfaces of both tubs to remove grime and rust. There are many stories on the actual clutch replacement, so won't go into too much detail but some lessons learned. Keep track of the way all the plastic aggitator pieces go in, plus the washers and clips along the way. Deep well 1/2" I think socket for the tub, it's litely spring loaded so look before you set it down. Punching off the nut on the tub worried me, but it was no big deal. Loosens and tightens the normal directions, no positive tight stop, just compression so pay attention to how tight and hard you pounded to get it off. Drain the water from the inner tub before getting too far. I took the four springs off and removed both tubs to clean. No more complaining about brown spots on clothes. Get the whole clutch kit, not just the band, even though it's probably just the band worn out. The plastic clutch engaging piece will probably be fatigued. The motor etc is heavy, and buffered it's drop with rags. tip on side when putting it back, because its a bear to try to lift up. I lightly greased some moving parts, just not much as to not cause band grip problems. The wire retaining clip is tricky- I put the hook end in first, used pliers to try and compress, and screwdriver to push down and in. The whole things wants to spin while you do this, but when it finally goes, it stays. I was concerned about the location of the band spring in relation to it's actuator when putting it together, but it turned out if you put it anywhere where the clutch is free to spin, it will engage normally. The top lid has two rubber bumpers, one fell off and landed on the front bottom corner of the cover which didn't help reinstallaion until my 8year old noticed it! Took a number of tries but finally got the four guides from the frame into the cover. I tried bringing it in level, front tipped sligthly up, front tipped slightly down; in the end I won't be much help, it just finally went. It wasn't as easy as most people said it would be, but my back hurt and I had kids "help", and it took just under two hours. Works amazingly well now. Parts arrived Two days after ordering, with no expiditing!
Read less
Was this helpful?
Thank you for voting!
drum SLAMMING into the back of the washer when sipnning
5 of 6 people
found this instruction helpful.
-
WILLIAM from DAYTON, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago
Was this helpful?
Thank you for voting!
slow spin
4 of 4 people
found this instruction helpful.
-
eugene from abbott, TX
- Really Easy
- 30 - 60 mins
replace clutcher
Was this helpful?
Thank you for voting!
Drain hose leaking
4 of 4 people
found this instruction helpful.
-
Maryanne from BEND, OR
- Really Easy
- 30 - 60 mins
-
Pliers
Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.
Was this helpful?
Thank you for voting!
Lid Switch Case was Broken and would not hold screws. Not draining or spinning.
4 of 4 people
found this instruction helpful.
-
Michael from ATASCADERO, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
I watched a youtube video made by the site on how to replace the lid switch assembly. It showed you exactly how to do this repair. Without watching the video, it would probably have stumped me. After watching the video a couple of times, it was really pretty easy to do. The timer on our washer also needed replacing. I followed the i
... Read more
nstructions by Joe from Covington, GA. That repair was really easy. Thanks, Joe, for the easy to follow, complete instructions.
Read less
Was this helpful?
Thank you for voting!
Washer Control Knob Broken
6 of 10 people
found this instruction helpful.
-
GARY from ORIENT, OH
- Really Easy
- 1- 2 hours
Installed new control knob as directed in the installation instructions found online at your website. Repair went exactly as described.
Was this helpful?
Thank you for voting!
washer would not spin or agitate
6 of 10 people
found this instruction helpful.
-
Doreen from Ashtabula, OH
- Easy
- 1- 2 hours
-
Screw drivers, Socket set, Wrench (Adjustable)
I first took the 2 screws out and disconnected the wires, I got my parts ordered and when they came in I put it back together then plugged th wires back in. I really could not believe that I could do something of this nature but when I started it was easy. My boyfriend wanted to take the washer to a repair shop, but I said first I
... Read more
will take a look and see if it will be worth saving. Otherwise I will junk it. It cost me with shipping costs 41.00 I am very proud of my self.
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washing machine making a grinding noise
4 of 4 people
found this instruction helpful.
-
Tracy from Yuba City, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three
... Read more
days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!
Read less
Was this helpful?
Thank you for voting!