11082467310 Kenmore Washer - Instructions

All Instructions for the 11082467310
121 - 135 of 1104

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer motor burned out
6 of 8 people found this instruction helpful.
  • Joseph from SANFORD, NC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1. Watch a video on installation, there are many on the internet.
(unplug the washer)
2. remove the screws on the back of the control panel to lift the control panel out of the way.
3. use a flat head screwdriver to remove the clips that hold the cabinet to the back panel.
4. disconnect the lid switch from the control panel by removing the clip that connects them at the top of the cabinet.
5. tilt the cabinet forward to remove it.
6. use a flat head screw driver to remove the two clips that hold the water pump to the motor and swing the water pump out of the way.
7. use a nut driver to remove the shipping screw that holds the clips on to the motor.
8. disconnect the wiring harness from the motor
9. remove the two clips from the motor with a flat head screwdriver and remove the motor
remove the three prong coupler and rubber gasket from the old motor and put them on the shaft of the new motor
10. remove the 4 rubber pads from the old motor and slide them onto the new motor.
11. insert the new motor into the washer aligning the prongs of the coupler.
12 reassemble the washer in reverse order of disassembly
(the shipping screw does not need to be reinserted into the spring clip that holds the motor)
Was this helpful?
Thank you for voting!
Cracked drain tube.
6 of 8 people found this instruction helpful.
  • Eric from Grand Haven, MI
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Removed old tube and replaced with new version. Replacement slightly different than original since the new part included a feature that appears to prevent the problem. New part still fit and is operating well so far.
Was this helpful?
Thank you for voting!
tub would not spin....burning smell
6 of 8 people found this instruction helpful.
  • John from Elm Mott, AL
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Unplugged washer. Pulled the washer away from the wall & leaned it back against the wall to access the underneath side of the washer. Disconnected water hoses to the pump with water pump pliers. Have drain pan handy to catch the water, approximately 1 qt. Remember which hose goes to the proper place. Removed two retaining screws/st raps allowing the motor to be seperated from the transmission. There is enough slack in the wiring to allow you to drop the motor without disconnecting. You do not need to remove the water pump. Removed old coupling & replaced with the new one. Make sure you use the "new style" replacement coupler or you will be doing this repair again very soon! Schematics are available online.
Was this helpful?
Thank you for voting!
Replacing water inlet valve with new one
5 of 5 people found this instruction helpful.
  • David from HENRY, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her )
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people found this instruction helpful.
  • Matthew from Wauwatosa, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
Loud Screeching noise when draining water
5 of 5 people found this instruction helpful.
  • Steven from Port Saint Lucie, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
On this model, no need to tip washer on back. Tilt console back and disconnect lid switch. Remove two clips holding back to top of washer (under console). Then remove top and front as directed in the video. The pump is accessible from the front of the unit, just below the tub. Hose clamps are easy to remove/replace. Took more time to wipe inside of washer clean than to remove/replace the water pump. Total time was just over 30 minutes.
Was this helpful?
Thank you for voting!
Washer would not fill with water...
5 of 5 people found this instruction helpful.
  • Eddie from Charlotte, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Watched the video on the website... and did what it said to do. It was VERY helpful... It did not fix the problem... so now I'm on to the next possible solution. Also, provided by the website. The valve was the problem 85% of the time. The water level switch is the problem 10% of the time. The water level switch is what I ordered nex t.
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell
Was this helpful?
Thank you for voting!
1. No hot water and cold water filled very slowly. 2. Washing machine severely vibrated and was very noisy.
5 of 5 people found this instruction helpful.
  • Janice from BLUE SPRINGS, MO
  • Very Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
EXACTLY as your video demonstrated.
Was this helpful?
Thank you for voting!
slow or no spin
6 of 9 people found this instruction helpful.
  • Steven from Wausau, WI
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
First read up on what others did and tried to find free repair manual with little luck. Called repairman, they thought whole transmission was shot- would have been $70 just to have them look- forget it. Getting it apart: popped off the two console cosmetic panels to get to a screw on each side from the top. Lifted off console, levered and squeezed retaining clips. Unhooked two connectors and overflow tubing? Shell pulled off easily, getting back on after I was all done made me wonder if it was a good choice. In the end yes- allowed me to clean inside surfaces of both tubs to remove grime and rust. There are many stories on the actual clutch replacement, so won't go into too much detail but some lessons learned. Keep track of the way all the plastic aggitator pieces go in, plus the washers and clips along the way. Deep well 1/2" I think socket for the tub, it's litely spring loaded so look before you set it down. Punching off the nut on the tub worried me, but it was no big deal. Loosens and tightens the normal directions, no positive tight stop, just compression so pay attention to how tight and hard you pounded to get it off. Drain the water from the inner tub before getting too far. I took the four springs off and removed both tubs to clean. No more complaining about brown spots on clothes. Get the whole clutch kit, not just the band, even though it's probably just the band worn out. The plastic clutch engaging piece will probably be fatigued. The motor etc is heavy, and buffered it's drop with rags. tip on side when putting it back, because its a bear to try to lift up. I lightly greased some moving parts, just not much as to not cause band grip problems. The wire retaining clip is tricky- I put the hook end in first, used pliers to try and compress, and screwdriver to push down and in. The whole things wants to spin while you do this, but when it finally goes, it stays. I was concerned about the location of the band spring in relation to it's actuator when putting it together, but it turned out if you put it anywhere where the clutch is free to spin, it will engage normally. The top lid has two rubber bumpers, one fell off and landed on the front bottom corner of the cover which didn't help reinstallaion until my 8year old noticed it! Took a number of tries but finally got the four guides from the frame into the cover. I tried bringing it in level, front tipped sligthly up, front tipped slightly down; in the end I won't be much help, it just finally went. It wasn't as easy as most people said it would be, but my back hurt and I had kids "help", and it took just under two hours. Works amazingly well now. Parts arrived Two days after ordering, with no expiditing!
Was this helpful?
Thank you for voting!
drum SLAMMING into the back of the washer when sipnning
5 of 6 people found this instruction helpful.
  • WILLIAM from DAYTON, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago
Was this helpful?
Thank you for voting!
Drum would not spin to drain water
9 of 18 people found this instruction helpful.
  • Gay from Apple Valley, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.
Was this helpful?
Thank you for voting!
Washer Control Knob Broken
6 of 10 people found this instruction helpful.
  • GARY from ORIENT, OH
  • Really Easy
  • 1- 2 hours
Installed new control knob as directed in the installation instructions found online at your website. Repair went exactly as described.
Was this helpful?
Thank you for voting!
The washer would drain, but was screaming while doing nothing else.
4 of 4 people found this instruction helpful.
  • Richard from JAMESTOWN, PA
  • Really Easy
  • More than 2 hours
The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The ne wly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
Was this helpful?
Thank you for voting!
Washer excessive vibration during rinse spin
4 of 4 people found this instruction helpful.
  • John from ODESSA, TX
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash bask et, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.
Was this helpful?
Thank you for voting!
washer would not spin or agitate
6 of 10 people found this instruction helpful.
  • Doreen from Ashtabula, OH
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
I first took the 2 screws out and disconnected the wires, I got my parts ordered and when they came in I put it back together then plugged th wires back in. I really could not believe that I could do something of this nature but when I started it was easy. My boyfriend wanted to take the washer to a repair shop, but I said first I will take a look and see if it will be worth saving. Otherwise I will junk it. It cost me with shipping costs 41.00 I am very proud of my self.
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw
Was this helpful?
Thank you for voting!
All Instructions for the 11082467310
121 - 135 of 1104