11082182200 Kenmore Dryer - Instructions

First and foremost turn power off to dryer at main box. Next remove screws say lint filter, then gently pry right and left front corners up with putty knife. Raise top and secure. Disconnect switch wire by using flathead sliding in between connection. Next remove 2 screws under front opening to dislodge switch. Repeat process in reverse order...takes 30 min. tops...

I remove the lint trap and the two screws that held the top down. Next to unscrew the two screws that holds the door switch. I prized the top up with a screwdriver . I unplugged the door switch and plugged in the new one. I inserted the switch into the door and replace the screws. I snapped the top back into place and replace the screws in the lint trap. I close the door and turn the dryer on and it worked. I followed the directions you provided on line. They were very easy to follow.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

The videos showed the tech taking the front off the unit but my unit didn't play that game. Instead all I had to do was take the top loose, (don't forget to take the dryer vent screws out first, that was the first beer) then access to the switch was easypeezy. That coupling for the switch assembly was 2 beers long. Anyways, got it all back together and it works like it's suppose to.

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Disassembled dryer, removed tumbler, replaced drum support rollers

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

just put the new part in the door---sooo easy! THANK YOU!

Pop out the old latch and replaced with a new one

Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)