- Home
- 11081476830
- Instructions
11081476830 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Slow running cold water to washer.
1 person
found this instruction helpful.
-
Phillip from EATONTON, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposin
... Read more
g rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646
Read less
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people
found this instruction helpful.
-
satyavenkata from Bentonville, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
No problems
1 person
found this instruction helpful.
-
Wayne from ZEPHYRHILLS, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple
Was this helpful?
Thank you for voting!
water inlet valve bad
1 person
found this instruction helpful.
-
linville from lily, KY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
received valve as ordered a simple installation. everything went well.home owner can do this repair
Was this helpful?
Thank you for voting!
Water would not stop running
2 of 4 people
found this instruction helpful.
-
Judy from BERNVILLE, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Followed by installation on line
Was this helpful?
Thank you for voting!
Water would not stop coming in when ran all the time
1 person
found this instruction helpful.
-
Norwood from Peachbottom, PA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
unscrewed the back removd thr two screws for the element unhooked the hose to machiine unpluged the electric to element and than replaced new element and plugged electric to element and hooked back the hose and replaced screws too the back and replaced back an screws
titled wash machine up hooked hoses for the water and plugged el ... Read more ectric and put drain hose back to drain done
titled wash machine up hooked hoses for the water and plugged el ... Read more ectric and put drain hose back to drain done
Read less
Was this helpful?
Thank you for voting!
water valve neede replaced
2 of 4 people
found this instruction helpful.
-
Timothy from summerfield, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the
... Read more
part so fast.
Read less
Was this helpful?
Thank you for voting!
When washer was in cold water rinse cycle, loud squealing noise.
1 person
found this instruction helpful.
-
James from LEXINGTON, KY
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers
unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clam
... Read more
p #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.
Read less
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people
found this instruction helpful.
-
Enrique from Miami Shores, FL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w
... Read more
asher door bang shut.Took longer than expected, but each procedure was simple.
Read less
Was this helpful?
Thank you for voting!
Cold water input into the washing machine was very slow.
1 of 2 people
found this instruction helpful.
-
James R from Birmingham, AL
- Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
The hot water hose was frozen to the hot water bibb and it took me a while to cut it loose with my Dremel tool. Removed the cabinet and replaced the water inlet valve easily, then hooked up new hot and cold water hoses. Reinstalling the cabinet was a little tricky getting it lined up correctly. Checked for leaks then tested the washing
... Read more
machine and it ran great with the water filling the machine much faster with the new Water Inlet Valve. I will definitely replace the washing machine hot and cold water hoses every 5 years from now on.
Read less
Was this helpful?
Thank you for voting!
No hot water flow, cold water flow very slow
1 of 2 people
found this instruction helpful.
-
Steve from Minneapolis, MN
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
It is sometimes tricky to figure out which screws and panels to remove to get to the parts you want to fix. Older Whirlpools used to have a lift up top that would allow access. This one required the back to come off (or at least partially off).
First, pull out the washer for access. Turn off water to the machine, and unplug the ... Read more electrical cord. Remove the drain hose using a large pliers to pinch the clamp and then pull the hose off. Remove water lines at the back of washer, again with a large pliers (if needed). Remove two screws at the bottom of back panel. Remove two screws at the top corners of back panel that hold some sort of plastic hinge piece to the control housing. Remove two screws on either end of the bottom front of the control housing on top of the machine. The back can now be lifted free (with some effort) from the sheet metal tabs that hold the bottom of the back in place. Reach in the bottom side with the pliers and disconnect the large drain line clamp so you have more room to swing the back out. There also might be a little plastic thingy to twist out of a slot in the back (maybe a vibration damper?) You will see the water inlet valve just inside the back on the side. The inlet hose connections are actually a part of the inlet valve. It is now possible to reach in from the side and disconnect the small water feed line from the inlet valve with a pliers, and disconnect the electrical plugs from the valve. Remove the two screws holding the valve to the back and remove the valve.
Reassembly is actually easier than removal. Don't forget to replace the water hose washers or they will probably leak. If the hoses look bad, just buy a new set. They can be had quite cheap.
Good luck and prepare to be proud of how well your "new" washer now works and how much money you saved!
p.s. PartSelect Rocks!
First, pull out the washer for access. Turn off water to the machine, and unplug the ... Read more electrical cord. Remove the drain hose using a large pliers to pinch the clamp and then pull the hose off. Remove water lines at the back of washer, again with a large pliers (if needed). Remove two screws at the bottom of back panel. Remove two screws at the top corners of back panel that hold some sort of plastic hinge piece to the control housing. Remove two screws on either end of the bottom front of the control housing on top of the machine. The back can now be lifted free (with some effort) from the sheet metal tabs that hold the bottom of the back in place. Reach in the bottom side with the pliers and disconnect the large drain line clamp so you have more room to swing the back out. There also might be a little plastic thingy to twist out of a slot in the back (maybe a vibration damper?) You will see the water inlet valve just inside the back on the side. The inlet hose connections are actually a part of the inlet valve. It is now possible to reach in from the side and disconnect the small water feed line from the inlet valve with a pliers, and disconnect the electrical plugs from the valve. Remove the two screws holding the valve to the back and remove the valve.
Reassembly is actually easier than removal. Don't forget to replace the water hose washers or they will probably leak. If the hoses look bad, just buy a new set. They can be had quite cheap.
Good luck and prepare to be proud of how well your "new" washer now works and how much money you saved!
p.s. PartSelect Rocks!
Read less
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people
found this instruction helpful.
-
Daniel from TRENTON, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said.
... Read more
I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Read less
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people
found this instruction helpful.
-
Rick from BETHESDA, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
Washer exhibited LOW cold water flow and dripping when off.
1 of 2 people
found this instruction helpful.
-
Cory from Alexandria, VA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
The repair went great. The video shown on the partselect site saved me a huge amount of time disassembling the cabinet to access the malfunctioning part. The most difficult part of the repair was replacing the cabinet on the unit after the part swap and getting it straight. Luckily 2 attempts was enough. I recommend trying this repair
... Read more
yourself and saving a bunch of $$.
Read less
Was this helpful?
Thank you for voting!