110799 Kenmore Dryer - Instructions

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi ... Read more ng me out!!!

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I ... Read more will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.

Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.

I removed 5 screws from the back of the top panel, removed the back panel, removed the start button from front of dryer, twisted the old start switch from the back, removed the two leads, reinstalled new part in reverse order. It was that simple! 15 minutes top. Dryer works fine. Gave me a chance to vacuum out all the dust bunnies and ... Read more clean out the dryer vent pipe as well.
Thanks!

I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.

First I tried a new switch, This did not fix the problem. Then I replaced the Fuse in the back of the unit.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Unfortunately it is not easy to get to this part due to the fact the control panel is attached to the top of the dryer by both plastic clips and screws. I was able to bend the back down in the back to gain access to the two screws that held the dryer timer in place. This job is much easier if you have an assistant to hold the thin tin o ... Read more r steel backing away from the control panel while reconnecting the wire sensors to the new timer. This is the second time I have used Parts Select they are excellent and their prices are very competitive. The part was identical to the broken part. I saved at least $100 by doing the job myself.

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above step ... Read more s in reverse order and your done.

Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This t ... Read more ook maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!

Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.

First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the ... Read more part they broke!

So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.

Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.

Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.

Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.

Easy, right?

Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h ... Read more e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.